!WARNING!
GETTING STARTED
• This Paintball Marker is NOT A TOY. Misuse can cause serious
• Tank valves must be installed or removed by qualified personnel.
1. Screw the 2-piece barrel into the marker’s body.
• All tanks must be retested before the expiration date.
2. Place barrel blocking device on the tip of the barrel.
• Improper use, filling, storage of this air tank may cause death, serious injury and property damage.
3. Turn the knob, on the front of the On/Off Bottom ASA (OFBA2), counterclockwise. Attach the air tank by turning it clockwise into the ASA, until it stops. Turn the knob on the On/Off ASA Clockwise, until it is flush with the body of the ASA. CAUTION: Do not use hand tools to screw the air tank into the bottom ASA.
IMPORTANT SAFETY INSTRUCTION AND GUIDELINS
injury or death.
• Recommend 18 years or older to purchase this product. Person under 18 must have adult supervision. • Read this manual, understand and follow the manual instructions for using this product. • Eye and face protection specially designed for paintball use, must be worn by user and persons within range at all times. • Treat all paintball markers as if it were loaded and able to fire. • Never look down the barrel or breech area of a marker. • Always use barrel blocking device when the marker is not in use. • Always chronograph this marker before playing paintball. • Never shoot any marker at velocities exceeds 300 FPS (Feet Per Second), or velocities which is greater than local fields or national laws allow. • Ensure all air lines and fittings are tightened and secured before installing the air tanks.
IMPORTANT CO2/ HPA AIR TANK SAFETY INSTRUCTION AND GUIDELINES
• Air tanks must be filled only by properly trained personnel. • Do not over pressurize. Do not expose pressurized tanks to temperatures in excess of 130F° degrees (54°C). • Do not expose tanks to corrosive materials and do not clean with caustic cleaners.
5. Remove the barrel blocking device from the tip of the barrel.
• Do not alter tanks in any way. • Tanks heated up to a temperature of 250F° degrees (54°C) or more must be condemned or re-qualified. • Keep air tanks out of reach of children. • The valve should NEVER detach from the tank canister. Should this occur, seek assistance from a qualified airsmith immediately. • Air tanks are use for the sport of paintball only.
• Do not shoot at people, animals, houses, cars or anything is not related to the sport of paintball.
• Fire only 0.68 caliber paintballs with this marker.
7. Push the trigger’s safety switch from right to left. The marker is now ready to fire.
GETTING THE MARKER READY FOR STORAGE
2. Remove the paintball hopper/loader from the marker’s feedneck and clear the breach of any remaining paintballs.
• Always make sure the bolt is in the un-cocked position when marker is not in use.
• This owner’s manual should always accompany this marker for reference and in the event of resale and new ownership.
6. Pump the handle back and pull it forward to its starting position.
1. Push the trigger’s safety switch from left to right. Tis will engage the safety and not allow the trigger to fire the marker.
• Always keep the marker in Safe mode until ready for use.
• Any modifications or tampering of original factory parts will cause all warranties and liabilities from Azodin.
4. Attach a paintball hopper/ loader to the marker’s feed neck.
3. Turn the On/Off ASA’s knob counterclockwise until you hear air escaping the ASA. STOP IMMEDIATELY
When removing the air tank from the marker, check to see if the regulator / bonnet is unscrewing from the tank. If so, stop unscrewing the air tank from the marker and contact a qualified airsmith for further assistance. Air tanks should unscrew from the marker’s On/Off ASA when the tank is turned counterclockwise. The regulator / bonnet should stay on the tank during the removal process. HPA / N2 air tanks store high pressure air. If this air is released without
4. Unscrew the tank from On/Off ASA. 5. Unscrew the barrel from the marker. 6. You may now store the marker.
VELOCITY ADJUSTMENTS
REGULATOR ADJUSTMENT
ASSEMBLY AND CLEANING THE MARKER Turn the End Cap Counterclockwise to access the internals PULL THE TOP COCKING KNOB
COUNTERCLOCKWISE DECREASE VELOCITY
CLOCKWISE DECREASE PRESSURE AND VELOCITY
CLOCKWISE INCREASE VELOCITY
COUNTERCLOCKWISE INCREASE PRESSURE AND VELOCITY COUNTERCLOCKWISE THE END CAP TO LET THE INTERNALS SLIDE OUT
WARNING: Do not turn the velocity adjust clockwie more than 6 turns. This may strip the threads on the Velocity Adjuster and End Cap. To increase your velocity FPS (Feet Per Second), use the allen wrench to turn the Velocity Adjuster (VA01) clockwise. To decrease your velocity FPS (Feet Per Second), use the allen wrench to turn the Velocity Adjuster (VA01) counterclockwise.
To increase the input pressure, use the allen wrench to turn the Rock Steady Seat (RSS2) counterclockwise. To decrease the input pressure, use the allen wrench to turn the Rock Steady Seat (RSS2) clockwise. NOTE: Contact [email protected] for more information on tuning the KP-III. Always use Velocity Adjustor (VA01) to increse velocity first then increase input pressure. RESET THE REGULATOR TO FACTORY PRESSURE 1. Please remove air source and clear the air stored in the marker. 2. Turn the Rocksteady Seat clockwise till it stops (DO NOT FORCE IT PAST THE STOP POINT). 3. Turn the RockSteady Seat counterclockwise two and half turns.
WARNING: Never remove the internals of the marker while the tank is attached to the marker. Always remove the loader, the air tank, and all paintballs from the marker before disassembly.
TROUBLESHOOTING
1. Pull the Top Cocking Knob (PBP3) up.
WARINIG: Remove all paintballs, loaders, and air tanks before disassembling the marker.
2. Pull the Bolt (PB03) out the back of the Pump Sled (PA01)
Symptoms
Repair Step(s)
Leaks down the barrel / body and
1. Tighten M8 x 8L Screw
Leaks from Pump Guide (PG01) / Zero
1. Replace R010 Oring
trigger frame
The first 1023 words, extracted from the PDF. Read the full manual above, or download it.