! WARNING !
! WARNING ! IMPORTANT SAFETY INSTRUCTION AND GUIDELINES
IMPORTANT HPA AIR TANK SAFETY INSTRUCTION AND GUIDELINES
• This Paintball Marker is NOT A TOY. Misuse can cause serious injury or death.
• Tank Regulators must be installed or removed by qualified personnel.
• It is recommended that a person be 18 years or older to purchase this product.
• All tanks must be retested before the expiration date.
Person under the age of 18 must have adult supervision or consent. • Please read the manual and follow the instructions for using this product.
property damage.
• Eye and face protection specially designed for paintball, must be worn by users and persons within range at all times.
• Do not over pressurize. Do not expose pressurized tanks to temperatures in excess of 130F° degrees (54°C).
• Never look down the barrel or breech area of a marker.
• Do not expose tanks to corrosive materials and do not clean with caustic cleaners.
• Always use barrel blocking device when the marker is not in use.
• Do not alter tanks in any way.
• Always chronograph this marker before playing paintball.
• Tanks heated up to a temperature of 250F° degrees (54°C) or more must be
• Never shoot any marker at velocities exceeds 300 FPS (Feet Per Second), or .
• Keep air tanks out of reach of children.
• Always chronograph the marker before playing.
• The Regulator should NEVER detach from the tank canister. Should this occur, seek
• Air tanks are to be used for the sport of paintball.
• Do not shoot at people, animals, houses, cars or objects that are not related to the sport of paintball. • Always keep the marker in Safe mode until ready for use. • Only use 0.68 caliber paintballs with this marker. • Always make sure the bolt is in the un-cocked position when marker is not in use. will void all warranties and liabilities from Azodin. • This owner’s manual should always accompany this marker for reference and should be presented to the new owner if there is transfer of ownership.
ZEN OLED DISPLAY
QUICK SET UP 1) Screw on the barrel of the marker to the body. 2) Place the barrel blocking device at the end of marker’s
PRESS TOP BUTTON TO TURN ON YOUR ZII
barrel.
3) Unscrew the grip screws on the left side of the marker
and remove the left grip panel. Then plug in a name brand 9V battery to the battery harness. (PG. 10)
4) Install a HPA Tank. 5) Put on your Paintball Mask/Goggle and pull the top cocking pin to the cocked position. 6) Screw in the front knob on the On/Off ASA to pressure 1. Battery Indicator
the marker. 7) Remove Barrel Blocking Device from the marker. 8) Turn on the marker by pressing the top button once (Fig 1A).
2. Electronic Safety - Safety On Fig 1A
3. Tournament Lock - Disable
9) Turn off the electronic safety by pressing the lower button once.
4. Display Data - Eye On Rate of Fire (ROF)
10) Your marker is now ready to fire. Aim and pull the trigger to shoot.
5. Eye Sensor - Eye On and Safety Off
CAUTION: Make sure the marker is in the SAFE mode and always place a barrel blocking device on the marker's barrel when not in use.
USING THE ZEN OLED
6. Eye Sensor - Eye Off and Safety Off 7. Tournamemt Lock - Enable
ELECTRONIC SAFE
POWER ON THE ZEN OLED Push and hold the top button to switch on the Zen OLED.
POWER OFF THE ZEN OLED Push and hold the top button until the display show "POWER OFF". Release the top button to turn off the ZII marker.
SAFETY ON
SAFETY OFF
To turn on the Electronic Safety, press the lower button once and display will read “SAFE”. To turn off Electronic Safety, press lower button once and the indicator will change to indicating eye sensor system is ON (EYES ON).
BATTERY INSTALLATION
EYE SENSOR SYSTEM
ZII is compatible wirh 9 or 9.5 Volt Alkaline batteries. For best performance, please use named brand 9 or 9.5V battery.
1. Remove the Three Grip Panel Screws (S016) from the left side of grip panel (Fig 2A).
2. Attach the battery to the battery harness (Fig 2B). 3. Re-tighten the Three Grip Panel Screws (S016). (Fig 2C)
EYES ON
BALL DETECTED
NONE DETECTED
EYES OFF
Note: Allen Wrench (2.5 mm) is provided in the Spare Parts Kit.
To turn off the eye sensor system, press top button once and display will change from
(EYES ON) to
(EYES OFF).
To turn on the eye sensor system, press top button once and the indicator will change back to
(EYES ON).
A flashing indicates an Eye error. This is caused by debris blocking the eyes, broken paint covering the eyes, and/or the bolt is in the forward position (Please . read the troubleshooting section for solution).
ZEN OLED SOCKETS 1. Battery socket 2. Solenoid socket 3. Micro switch socket 4. Eye sensor system socket 5. Expansion board socket
Extracted from the PDF. Read the full manual above, or download it.