JT SPORTS ER2 PUMP PISTOL OPERATORS MANUAL The JT Sports ER2 Pump Pistol is non-serviceable and any attempts to repair or replace parts of the marker will void the warranty. For manuals and warranty details, go to: paintballsolutions.com. For manuals in other languages, (where applicable), go to: paintballsolutions.com W arnin g THIS IS NOT A TOY. MISUSE MAY CAUSE SERIOUS INJURY OR DEATH. EYE PROTECTION DESIGNED SPECIFICALLY FOR PAINTBALL MUST BE WORN BY THE USER AND PERSONS WITHIN RANGE. WARNING: This product contains one or more chemicals that are known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. You must be at least 18 years of age to purchase this product. This product may be mistaken for a firearm by law enforcement officers or others. Altering the color of the product or brandishing the product in public may be considered a crime.
Safe Marker Handling
CAUTION Never carry your marker uncased when not on a playing field. The non-playing public and law enforcement personnel may not be able to distinguish between a paintball marker and firearm. For your own safety and to protect the image of the sport, always carry your marker in a suitable marker case or bag. Safety and safe marker handling are the most important aspects of paintball sports. Please practice each of the following steps with an unloaded marker before attempting to operate your marker with an air source and paintballs. • Every person within range must wear eye, face and ear protection designed specifically to stop paintballs and meeting ASTM standard F1776. • Treat every marker as if it were loaded. • Never look down the barrel of a paintball marker. • Do not install an air source or load paintballs into your marker until you have completely read and understood this manual and feel completely confident with your ability to handle your marker safely. • Keep the marker’s Safety “ON” until ready to shoot. • Keep your finger out of the trigger guard and away from the trigger until you are ready to shoot. • Keep the barrel blocking device in/on the markers barrel when not shooting. • Store the marker unloaded and degassed in a secure place. • Follow warnings listed on the air source for handling and storage. • Do not shoot at fragile objects such as windows. • Remember that the ultimate safety device is you, the operator. • Never point the marker at anything you do not wish to shoot. • After removing propellant point marker in safe direction and discharge until marker is degassed. • Always measure your marker’s velocity before playing paintball and never shoot at velovities in excess of 300 ft/s (91.44 m/s) W arnin g Eye protective devices designed specifically for paintball use must be worn by the operator and anyone within range (fig. 1).
Mechanical Safety The Safety is a small mechanical push button above the trigger. When the Safety is “ON”, the red on the left side of the Safety will be not be visible and the marker will not fire. When the Safety is “OFF”, the red on the left side of the Safety will be visible. The Safety should be on at all times when the marker is not being fired (fig. 2). Barrel Blocking Device The barrel blocking device should be installed at all times when the marker is not being fired, along with the Safety being in the “ON” position, red not visible. To install Barrel blocking device, place plug into barrel end and push firmly until plug is fully into marker barrel (fig. 3). Installing 12 gram CO2 Cylinder Consult the dealer from whom you purchased your marker, or a recognized and competent air smith, for instruction in the safe handling of 12 gram CO2 cylinders before purchasing or installing one into your marker. X-Ray Goggle • Make sure the Safety is “ON” and that the barrel blocking device Figure. 1 is installed. • Remove the 12 gram plug on the bottom of the grip frame by turning it counterclockwise. • Install a new 12 gram cylinder with the small end going in first. • Re-install the 12 gram plug, turning it clockwise until the marker is pressurized. • Your marker is now pressurized and is ready to use. Loading Paintballs JT Sports markers use .68 caliber, water-soluble paintballs, readily available at paintball pro-shops, commercial playing fields, and many sporting goods stores. OFF ON • Make sure the marker’s Safety is “ON” and put on eye protective device designed specifically for paintball and make sure that anyone within range of the marker does the same. • Using the 10 round tube insert the tube with paintballs into the markers feed neck. • Your marker is now loaded and ready.
Removing 12 gram Cylinder • Before removing the 12 gram cylinder from your marker, make sure you leave your eye protective device designed specifically for paintball on and make sure that anyone within range of the paintball pistol does the same. • While pointing the marker in a safe direction, disengage the Safety (red visible). • Keeping the marker pointed in a safe direction and shot the marker until you do not hear it firing. • A small amount of air may remain in the 12 gram cylinder even if the marker does not fire. • Make sure the barrel blocking device is properly installed on the marker. • Slowly turn the 12 gram plug counter clockwise and remove the 12 gram cylinder. As you turn the plug, you will hear the remaining air vent out. • The marker is now ready to be cleaned and put away for future use. Cleaning Once your marker is unloaded and the 12 gram cylinder is removed, you can use a damp cloth to wipe off paint, dirt and debris from the outside of your marker. Do not use any petroleum based or aerosol products on your marker. Petroleum based and aerosol products can damage your markers o-rings and can damage the markers plastic components. Clean the barrel of the marker by pulling a squeegee thru the marker. When you are finished using your marker it is important that you prepare it for storage. This will not only serve to increase…
The first 1049 words, extracted from the PDF. Read the full manual above, or download it.