JT DL9 Manual - English

GRIP ASSEMBLY RETAINING SCREW Tornillo de Aseguramiento Vis d’arrèt GRIP ASSEMBLY Armazón de Cacha Crosse

SAFETY Seguro Verrou de sécurité

MAGAZINE Magasin Tambor

LUBRICATION POINTS PUNTOS DE LUBRICACIÓN POINTS DE LUBRIFICATION

USER’S MANUAL

RULES OF SAFE PAINTBALL MARKER HANDLING 1. Read these instructions before using this product. 2. Do not use unless everyone within range is wearing eye, face and ear protection designed specifically to stop paintballs and complies with specification ASTM F1776. 3. Never point the paintball marker at anyone that is not wearing a paintball mask that complies with specification ASTM F1776. 4. Do not modify your marker’s pressurized air system or cylinder in any way. 5. Keep the marker on safe until ready to shoot 6. Never use anything other than .68 caliber paintballs. Do not attempt to shoot used paintballs. 7. Treat every marker as if it were loaded. 8. Never look down the barrel of a paintball marker. 9. Keep your finger off the trigger until ready to shoot. 10. Never point the marker at anything you don’t wish to shoot 11. Keep the barrel blocking device in/on the marker’s muzzle when not shooting. 12. Keep the paintball marker on safe when not in use. 13. Always remove paintballs and propellant source before disassembly. 14. After removing propellant source, point marker in safe direction and discharge until marker is degassed. 15. Store the marker unloaded and degassed in a secure place. 16. Follow warning listed on the gas source for handling and storage 17. Do not shoot at fragile objects such as windows 18. Always measure your marker’s velocity before playing paintball and never shoot at velocities in excess of 91.44 m/s (300 ft/s) 19. Never engage in vandalism. 20. Some paintballs may cause staining of some porous surfaces such as brick, stucco, and wood.

BARREL PLUG Tapón del coñon Obturateur de canon

STEEL BRAIDED HOSE Manguera de Acero Tejido Tuyau en acier tressé

SINGLE TRIGGER Gatillo para do Dedos Détente à solo doigts

BOTTOM-LINE CONSTANT AIR ADAPTER Adaptador de Aire Constante de Linea Base Adaptateur d’air constant de ligne de fond

STEP 3. Attach a CO2/Compressed Air Tank to the Markers C/A adapter. Using a CO2/Compressed Air Tank firmly tighten clockwise to the Markers C/A adapter until it is snug. HELPFUL TIP: Make sure to have the CO2/ Compressed Air Tank filled before attaching. NOTE: O-rings in the Markers parts kit are NOT supplied to attach with a CO2/ Compressed Air Tank. IMPORTANT: You should never need to use any hand tool to attach a CO2/ COMPRESSED AIR TANK to the Markers C/A adapter. STEP 4. Attach the Magazine to the Trigger Housing or attach Paintball Loader to the Marker’s clamping feed neck and tighten the screw. NOTE: The loader and Magazine can only be filled with .68 Caliber Paintballs. NOTE: Add 3 drops of mineral oil to the ASA adapter prior to attaching the refillable cylinder. Check the website at: www.paintballsolutions.com for approved lubricants. STEP 5. Cocking the Marker. Pull back the Side Cocking Handle until you hear and feel the bolt latches. CAUTION: Should you let go of the Side Cocking Handle before it latches, your Marker may fire.

REFILLABLE CYLINDER (not Included) Cilindro Rellenable (no Incluida) Cylindre Réutilisable (non fournie)

CAUTION: This product is intended to be used at a velocity no greater than 300 feet per second (fps). Paintball markers are not intended to shoot within 10 feet. WARNING: The paintball Marker may have excess gas after removal of the Co2/ Compress Air Tank. Death or serious injury may occur if all paintballs and air is not discharged prior storing the marker. WARNING: Never store Co2/ Compressed Air Tanks attached to the marker. Death or serious injury may occur if marker is stored with air source still attached. WARNING: Serious injury or even death might occur if individuals are within 300 feet (100 meters) of a shooting ranger without proper eye protection.

Unloading Your Marker WARNING: Always wear proper eye, face, and ear protection designed especially to stop paintballs while unloading and working on your paintball marker. STEP 1. Make sure barrel plug is securely in barrel. STEP 2. Put marker on safe. (Push left to right)

STEP 6. Remove the barrel blocking device in the barrel. Now you can release the safety button.

STEP 3. Remove magazine and remove loader – Loosen the feed neck set screw and remove paintball loader. When removing the loader, make sure to remove all paintballs.

CAUTION: With the safety button released in the FIRE position the Marker is ready to shoot/play. By pulling the Trigger the marker will fire a paintball.

CAUTION: There may be paintballs in the Marker’s breach; remove barrel plug and take a couple of shots in a safe direction.

Field Strip Guide

STEP 8. When finished playing, remove all paintballs from the Magazine and Loader. Then detach the loader from the Markers feed neck by loosening the set screw on feed neck clamp.

- Read the manual thoroughly before using the marker. - Lubricate all O-rings in the marker using ONLY mineral oil. - Place 3 drops of mineral oil in ASA with each change of gas source. - Familiarize yourself with the exploded diagram provided in the manual before disassembly. - Wipe off all parts before re-assembly. - Re-lubricate O-rings before re-assembly. - NEVER immerse the marker in water. Water will cause internals to rust. - Call customer service if you have further questions at 1-800-220-3222.

STEP 9. The Marker needs to be in the SAFE MODE and un-cocked after each use.