Yakuza Series USB board for the Bob Long Closer, Marq, Vice, & Protégé Tengu Graphical Pixel Editor by Tadao Technologies LLC, pat. pend. 4C™ Technology by Extreme Paintball Design LLC, pat. Pend. FEATURES • • • • • • • • • •
Fully functional in the Bob Long Closer, Marq, Vice, and Protege Includes super thin Stinger grip panels with a window for the OLED display Licensed 4CTM technology enables automatic detection and use of 4 Eye boards to dynamically maximize rate of fire and reduce chops Yakuza Series OLED graphical display system which shows eye status, battery life, current fire mode, max rate of fire, game timer, and menu system Microchip PIC18F2550 microcontroller runs at up to 48 Mhz and provides Full Speed USB 2.0 (12Mbit/s) Tengu USB interface for Windows XP and Vista provides free firmware updates, custom boot screens, settings adjustments, and more Zero power drain while turned off (less than 0.0001 mA) Industry first anti-breech bounce software reduces chopping when a loader is running out of paintballs RF socket and wiring harness included to support Magna, Pulse, and other RF transmitters Multiple modes of fire ensure compliance with all major tournament series: unlimited semi-automatic, adjustable semi-automatic, PSP ramping, PSP 3 round burst, NXL full-automatic, Millennium ramping, custom ramping, auto-response, 3 round burst, and full-automatic Tadao trigger logic asynchronously monitors the trigger switch, using an interrupt based scan at up to 12 million times per second for the quickest response time and fastest semi-automatic Tadao dynamic eye logic watches for the bolt to return every shot, cycling the marker as fast as possible Rate of fire adjustable from 5 to 30 bps in 0.1 bps increments, plus unlimited rate of fire Extremely easy to use OLED graphical and text based menu system for changing settings All settings are stored in non-volatile memory so they are not lost when the battery is disconnected Spring battery contacts so there’s no wiring harnesses to break or wear out Five custom user profiles allow you to save settings for specific tournament series or performance tuning Additional features include adjustable debounce, anti-mechanical bounce, cycle percentage filter, anti-bolt stick, ball in place delay, bolt delay, eye modes, ramp start, ramp percentage, breakout modes, game timer, auto power down timer, shot counter, screen brightness, and more High quality Omron 80 gram trigger microswitch
INSTALLATION Installation of the Yakuza board must be carefully done to avoid damaging the electronics or wiring harnesses. 1. Remove the grip panel from the left side of the grip frame, exposing the battery and circuit board. 2. Remove the battery and unplug the 8 pin wiring harness. 3. Remove the 3 mounting screws. 4. Gently pull the board out of the frame. If you use a spring to return the trigger, make sure to keep track of it and the return spring bracket that sits over the trigger switch. 5. Place the return spring bracket on the Yakuza board’s trigger switch. 6. Insert the Yakuza board into the grip frame. 7. Replace the 2 mounting screws for the trigger switch and the single screw down at the bottom of the board. Do not over-tighten. 8. Replace the battery. The positive terminal is towards the front of the frame, as shown by the + and – marks on the surface of the board. 9. Replace the grip panels. BOARD OPERATION Turn on the board by pushing the power switch. The OLED display will show the boot screen, followed by the main screen with the current fire mode, rate of fire, battery, and eye status visible. Turn off the board by pressing and holding the power switch for at least 1 second. The OLED display will turn off to indicate the board has shut down. The eye system is toggled on and off by quickly pressing and releasing the power switch. The OLED display will reflect the eye status.
The use of the 4C™ eye system allows for much faster rates of fire because it can anticipate the next paintball being loaded into the breech and start the firing cycle early, which negates the delay time found in the pneumatics of the paintball marker. The Yakuza software was written specifically to take advantage of this arrangement, and automatically uses the top eye set when the loader is feeding fast enough. It can also determine when the top eye set is blocked by paint or debris, and will default to using only the bottom eye until the top is clear again. Once the top eye is clear, it will resume use of both eye sets. If used, the eye system cycles the marker as fast as possible. During each shot the eyes watch for the bolt to return, ending the current firing cycle and starting another as quickly as the pneumatics allow. If the eye system is continually blocked (e.g. putting your finger in front of the eyes) and is unable to see the bolt return after every shot, the max rate of fire will be reduced to about 12 balls per second to prevent further chopping, and the OLED display will display an eye malfunction. Firing the marker with paint and air will utilize the eye system correctly, maximizing the rate of fire. The programming menu system is activated by holding down the trigger while pressing the power switch. The OLED display will show “Menu system initiated….” Further details regarding the menu system can be found below. If selected in the menu system, the game timer will replace the current rate of fire indicator on the OLED display. The game timer will start after the first trigger pull. USB Your Yakuza Series USB board has full USB 2.0 functionality, and works in tandem with the Tengu USB interface, which can be downloaded online at www.tadaotechnologies.com. Tengu allows you to update the firmware on your board, create and save custom boot screens, modify all the settings, and more. To run the Tengu interface you need a mini-B USB cable and a PC running Windows XP or Vista. XP users will also need to download the Microsoft .NET Framework 2.0 or newer. Refer to the…
The first 1022 words, extracted from the PDF. Read the full manual above, or download it.