Sly Yakuza Series USB Board For the Angel A1 and A1 Fly Tengu Graphical Pixel Editor by Tadao Technologies LLC, pat. pend. FEATURES • • • • • • • • • • • • • • • • •
Fully functional in the Angel A1 and A1 Fly Yakuza Series OLED graphical display system which shows eye status, battery life, current fire mode, max rate of fire, game timer, and menu system Microchip PIC18F2550 microcontroller runs at up to 48 Mhz and provides Full Speed USB 2.0 (12Mbit/s) Tengu USB interface for Windows XP and Vista provides free firmware updates, custom boot screens, settings adjustments, and more Zero power drain while turned off (less than 0.0001 mA) Industry first anti-breech bounce software reduces chopping when a loader is running out of paintballs RF socket and wiring harness included to support Magna, Pulse, and other RF transmitters Multiple modes of fire ensure compliance with all major tournament series: unlimited semi-automatic, adjustable semi-automatic, PSP ramping, PSP 3 round burst, NXL full-automatic, Millennium ramping, custom ramping, auto-response, 3 round burst, and full-automatic Tadao trigger logic asynchronously monitors the trigger switch, using an interrupt based scan at up to 12 million times per second for the quickest response time and fastest semi-automatic Tadao dynamic eye logic watches for the bolt to return every shot, cycling the marker as fast as possible Rate of fire adjustable from 5 to 30 bps in 0.1 bps increments, plus unlimited rate of fire Extremely easy to use OLED graphical and text based menu system for changing settings All settings are stored in non-volatile memory so they are not lost when the battery is disconnected Spring battery contacts so there’s no wiring harnesses to break or wear out Five custom user profiles allow you to save settings for specific tournament series or performance tuning Additional features include adjustable debounce, anti-mechanical bounce, cycle percentage filter, anti-bolt stick, ball in place delay, bolt delay, eye modes, ramp start, ramp percentage, breakout modes, game timer, auto power down timer, shot counter, screen brightness, and more High quality Omron 25 gram trigger microswitch
INSTALLATION Installation of the Yakuza board must be carefully done to avoid damaging the electronics or wiring harnesses. 1. Remove the grip panel from the right side of the grip frame, exposing the battery and circuit board. 2. Remove the battery and unplug the eye and solenoid harnesses. 3. Remove the front and rear frame mounting screws. 4. Remove the frame from the gun body. 5. Remove the 3 board mounting screws. 6. Gently pull the stock board out of the frame. 7. Gently remove the scroll wheel from the stock board and attach it to the Yakuza board scroll switch. 8. Insert the Yakuza board into the grip frame. 9. Replace the 3 board mounting screws. 10. Reattach the frame to the gun body. 11. Plug the eye and solenoid harness back into the appropriate sockets. 12. Replace the battery and grip panel. BOARD OPERATION Turn on the board by pushing the scroll wheel. The OLED display will show the boot screen, followed by the main screen with the current fire mode, rate of fire, battery, and eye status visible. Turn off the board by pressing and holding the scroll wheel for at least 1 second. The OLED display will turn off to indicate the board has shut down. The eye system is toggled on and off by rolling the scroll wheel up for 1 second. The OLED display will reflect the eye status. If used, the eye system cycles the marker as fast as possible. During each shot the eyes watch for the bolt to return, ending the current firing cycle and starting another as quickly as the pneumatics allow. If the eye system is continually blocked (e.g. putting your finger in front of the eyes) and is unable to see the bolt return after every shot, the max rate of fire will be reduced to prevent further chopping, and the OLED display will show an eye
malfunction. Firing the marker with paint and air will utilize the eye system correctly, maximizing the rate of fire. The programming menu system is activated by holding down the trigger while turning the board on. The OLED display will show “Menu system initiated….” Further details regarding the menu system can be found below. If selected in the menu system, the game timer will replace the current rate of fire indicator on the OLED display. The game timer will start after the first trigger pull. USB Your Yakuza Series USB board has full USB 2.0 functionality, and works in tandem with the Tengu USB interface, which can be downloaded online at http://www.tadaotechnologies.com/productcart/pc/viewContent.asp?idpage=15. Tengu allows you to update the firmware on your board, create and save custom boot screens, modify all the settings, and more. To run the Tengu interface you need a mini-B USB cable and a PC running Windows XP or Vista. XP users will also need to download the Microsoft .NET Framework 2.0 or newer. Refer to the Tengu user guide for information regarding USB installation and using the Tengu USB interface. OLED DIAGRAMS The OLED display built into the Yakuza series board shows the user a multitude of information via text and icons. The software is written with performance in mind, and will not update the screen until the user stops shooting for just a fraction of a second. This ensures that the screen does not interfere with the timings of the marker. The battery indicator shows battery life by displaying a bar within the icon. The longer the bar, the higher the battery level. A low battery is reached at approximately 7.5 volts, but if quality alkaline batteries are used, the remaining power should be adequate for at least one more case of paint. The eye indicator is displayed as a circular icon. The circular indicator shows when the eyes are blocked or malfunctioning. If the eye system is off, the indicator displays “off.” If the eye system has a malfunction from not seeing the bolt return, it will show an X.…
The first 1015 words, extracted from the PDF. Read the full manual above, or download it.