Yakuza Series USB Board Bob Long Intimidator Tengu Graphical Pixel Editor by Tadao Technologies LLC, pat. pend.
FEATURES Yakuza Series OLED graphical display system which shows eye status, battery life, current fire mode, max rate of fire, game timer, and menu system Microchip PIC18F2550 microcontroller runs at up to 48 Mhz and provides Full Speed USB 2.0 (12Mbit/s) Tengu USB interface for Windows 7, Vista, and XP provides free firmware updates, custom boot screens, settings adjustments, and more Zero power drain while turned off (less than 0.0001 mA) Industry first anti-breech bounce software reduces chopping when a loader is running out of paintballs RF socket supports Magna, Pulse, and other RF transmitters Multiple modes of fire ensure compliance with all major tournament series: unlimited semi-automatic, adjustable semi-automatic, PSP ramping, PSP 3 round burst, NXL full-automatic, Millennium ramping, custom ramping, auto-response, 3 round burst, and full-automatic Select fire functionality allows up to three separate fire modes to be accessed on the fly while playing Tadao trigger logic asynchronously monitors the trigger switch, using an interrupt based scan at up to 12 million times per second for the quickest response time and fastest semi-automatic Tadao dynamic eye logic watches for the bolt to return every shot, cycling the marker as fast as possible Rate of fire adjustable from 5 to 30 bps in 0.1 bps increments, plus unlimited rate of fire Extremely easy to use OLED graphical and text based menu system for changing settings All settings are stored in non-volatile memory so they are not lost when the battery is disconnected Spring battery contacts so there’s no wiring harnesses to break or wear out Five custom user profiles allow you to save settings for specific tournament series or performance tuning Additional features include adjustable debounce, anti-mechanical bounce, cycle percentage filter, anti-bolt stick, ball in place delay, bolt delay, eye modes, ramp start, ramp percentage, breakout modes, game timer, auto power down timer, shot counter, screen brightness, and more Includes a high quality Omron 80 gram trigger microswitch and replacement backplate with buttons to rid your marker of the flimsy membrane pad
INSTALLATION Installation of the Yakuza board must be carefully done to avoid damaging the electronics or wiring harnesses. 1. Remove the grip frame panel from the left side of the frame, exposing the battery and circuit board. 2. Remove the battery. 3. Remove the 2 mounting screws. 4. Gently pull the stock board out of the frame and unplug the power/solenoid and eye harnesses, and membrane pad. 5. Insert the Yakuza board into the grip frame while plugging in the power/solenoid and eye harnesses. 6. Replace the 2 mounting screws. 7. Slide the new switch contact block into the membrane pad slot, making sure the switch contacts stay in place and line up properly with the two switches on the board. 8. Replace the battery. 9. Replace the left grip frame panel. BOARD OPERATION Turn on the board by pushing the top button. The OLED display will show the boot screen, followed by the main screen with the current fire mode, rate of fire, battery, and eye status visible. Turn off the board by pressing and holding the top button for at least 1 second. The OLED display will turn off to indicate the board has shut down. The eye system is toggled on and off by pressing and holding the bottom button for 1 second. The OLED display will reflect the eye status. If used, the eye system cycles the marker as fast as possible. During each shot the eyes watch for the bolt to return, ending the current firing cycle and starting another as quickly as the pneumatics allow. If the eye system is continually blocked (e.g. putting your finger in front of the eyes) and is unable to see the bolt return after every shot, the max rate of fire will be reduced to prevent further chopping, and the OLED display will show an eye malfunction. Firing the marker with paint and air will utilize the eye system correctly, maximizing the rate of fire.
The programming menu system is activated by holding down the trigger while turning the board on. The OLED display will show “Menu system initiated….” Further details regarding the menu system can be found below. If selected in the menu system, the game timer will replace the current rate of fire indicator on the OLED display. The game timer must first be primed by holding down the trigger for 4 seconds. A “timer ready” message will flash on the display. The game timer will then start on the next trigger pull. SELECT FIRE Software releases dated after July 1, 2009, contain the new select fire functionality. This allows you to pick up to three different fire modes which can be cycled through during game play. The modes are chosen in the programming menu using the fire mode 1, 2, and 3 settings. You can choose to use just one (which disables select fire), two, or three modes at a time. If select fire modes are enabled, you can cycle through them during play by pressing the bottom button quickly. The OLED display will show the current fire mode as it changes. All fire modes share the same rate of fire setting, unless unlimited semi-automatic is chosen. This allows you to have combinations such as unlimited semi-automatic, 15 bps ramping, and 15 bps full-automatic. Unless specifically allowed, select fire functionality should not be used in tournaments. It is strongly advised to consult both tournament rules and local field regulations before use. Tadao Technologies LLC takes no responsibility for the user’s choice in using select fire functionality. USB Your Yakuza Series USB board has full USB 2.0 functionality, and works in tandem with the Tengu USB interface, which can be downloaded online at http://www.tadaotechnologies.com/productcart/pc/viewContent.asp?idpage=15. Tengu allows you to update the firmware on your board, create and save custom boot screens, modify…
The first 985 words, extracted from the PDF. Read the full manual above, or download it.