Spyder Stormer Manual - English

VELOCITY ADJUSTMENT INCREASE/DECREASE

A JAMMED PAINTBALL IN THE BREACH

HOW TO CLEAN THE MARKER

DISASSEMBLE / REASSEMBLE AND CLEANING OF REAR INTERNALS

CUP SEAL REMOVAL GUIDE

TROUBLESHOOTING

STORMER™ PARTS LIST

STORMER™ SCHEMATIC

WARRANTY STATEMENT

English IMPORTANT SAFETY GUIDELINES WARNING • • • • • •

This paintball Marker is NOT a toy. Misuse can cause serious injury or death. Spyder recommends that the customer be at least 18 years of age to purchase this product. Person under 18 years of age must have adult supervision when using this product. Read this User manual before using this product.

OPERATION GUIDE / START UP 1.

Always attach a barrel blocking device over the tip of the barrel for safety precautions when not shooting/ playing.

Spyder recommends having the Marker in the SAFE MODE position before use. To operate, push the safety button from the “PUSH SAFE” side of the Trigger Frame. This will position the Marker in a lock SAFE MODE. To disengage the safety button in a safely manner, point the Marker in a safe direction, and push the safety button towards the opposite side of the Trigger Frame. CAUTION: Do not disengage safety button until step 6.

3. tighten clockwise to the Markers C/A adapter until it is snug. HELPFUL TIP: Make sure to have the CO2/ NOTE: O-rings in the Markers parts kit are NOT supplied to attach with a CO2/Compressed Air Tank. IMPORTANT: You should never need to use any hand tool to attach a CO2/ COMPRESSED AIR TANK to the Markers C/A adapter. (SEE CO2/COMPRESSED AIR TANK WARNING)

accessories will void all warranties and liabilities from Spyder. Keep the barrel blocking device on Marker when not shooting/playing. To ensure proper adjustment of velocity Feet Per Second (fps), Spyder strongly recommends using The discharges of paintballs are high velocity and high impact that can cause serious injuries or death if misused. Before/after use of the Marker, check and make sure all screws are securely tightened. Loose screws may prevent the Marker from functioning properly. A paintball Marker NOT properly maintained can be dangerous and can cause serious injury or death. Any person using this product or within range of this product while it is in use MUST wear EYES/ limited to, performing a maintenance/velocity check and during target practice. Spyder reminds the user that SAFETY IS YOUR RESPONSIBILITY. Protect your eyes/face and ears at all times. Spyder will not be held liable for injuries or death sustained when failing to follow the safety guidelines. Never shoot or point your Marker at a person that is not in a designated paintball facility and without proper paintball EYES/FACE/EARS PROTECTION. The protection includes and not limited to the protection of eyes, face, ears, neck and head. Avoid shooting underneath the paintball goggles.

4. Attach the paintball loader to the Markers clamping feed neck and tighten the set screw. NOTE: Fill your paintball loader with only .50 caliber paintballs. 5.

6. Remove the barrel blocking device over the barrel. Now you can release the safety button. CAUTION: With a paintball. IMPORTANT: 7.

Performing a velocity (fps) check. Turning the Velocity Adjuster/Spring Guide clockwise will increase the velocity (fps) while turning counter-clockwise will decrease the velocity (fps). NOTE: Your Marker is intended to be used in a paintball facility with the proper paintball protection. IMPORTANT: Spyder recommends using a chronograph to ensure Marker’s velocity is under 300 (fps).

8. by loosening the set screw on feed neck clamp. CAUTION: There may be one paintball in the Marker’s breach; take a shot or two in a safe direction to make sure the barrel and Receiver are empty. 9. Place the barrel blocking device over the barrel tip. This will help avoid any accidental discharge. 10. Spyder recommends having the Marker in the SAFE MODE and un-cocked position after use.

Treat every paintball Marker as if it were loaded. Never look down the barrel of a loaded or unloaded Marker. Always keep the paintball Marker in SAFE MODE until ready to operate. Always remove the air source and all paintballs from the Marker, includes paintballs inside the breach of the Marker, before disassembly. Fire only .50 caliber paintballs with this product. The use of any foreign objects will VOID all warranties and liabilities from Spyder . Always make certain the bolt of the Marker is in the un-cocked position when not shooting/playing. law enforcement penalties if property damage is caused by the user. Never point or shoot your Marker at an animal. Never point the barrel toward yourself while playing, running or stumbling to avoid shooting underneath your paintball goggles. Wear appropriate dress to avoid any exposure of skin to protect you when playing paintball games. Transfer this User’s Manual upon change of Marker ownership. Please visit www.spyder50.com for the latest User Manual updates.

11. Unscrew the CO2/Compressed Air Tank from the Markers C/A adapter. By turning the tank counter clockwise will detach from the Markers C/A adapter. CAUTION: Never expose any skin underneath the C/A adapters bleed hole when removing the tank. This can run the risk of getting skin burn from the releasing of the GAS. IMPORTANT: You should never need to use any hand tool to detach a CO2/Compressed Air Tank from the Markers C/A adapter. (SEE CO2/COMPRESSED AIR TANK WARNING) 12. Store the Marker in a paintball bag or in a safe place. WARNING: Before/after use of the Marker, make sure to fasten all screws. Loose screws may prevent the Marker from functioning properly. HELPFUL TIP: It’s…