Spyder 2007 Mr2 Manual - English

the Handle latches, your marker may fire. Note: The Snap T-Cocking Handle will latch the bolt internally, the Handle will not remain in a cocked position after latching the bolt, nor will it move while the marker is being fired. You should hear an audible click and feel a tension release in the Handle when cocking the marker.

3) Tighten the Air Tank until it is snug. If a leak occurs between the Tank and the C/A Adapter, replace the Tank O-ring. 4) Install the Loader onto the Feed Adapter (part #54A). Tighten the Feed Adapter Screw to secure the Loader, then fill the Loader with .68 caliber paintballs only.

5) To change firing modes, slide the Selector Switch on the rear of the trigger frame to the desired mode. 6) It is recommended to use a motorized Loader that is capable of feeding paintballs into the marker at 13 balls per second or faster to avoid chopping paintballs in the markers breach when shooting at high rates of fire.

NAME: ADDRESS: C I T Y:

CO U N T RY:

7) Routine lubrication of the marker does not require disassembly of the marker. Put 3-4 drops of Paintball Marker Oil into the Bottom Line ASA (part #261), screw in your air tank, point the marker in a safe direction and dry fire (no paintballs in

the chamber) 5-10 shots. This procedure will circulate oil through the markers internal parts, thus extending the life of the marker.

PARTS LIST

! C AU T I O N ! This paintball marker is NOT a toy. It can cause serious injury or death. Kingman recommends that customers be at least 18 years of age to purchase this product. Firmly install a barrel blocking device when marker is not in use. All persons using this product, or within range while this product is being used, must wear eye and face protection specifically designed for paintball. Never shoot a person who is not wearing proper protection. Treat every paintball marker as if it were loaded. Never look down the barrel of the marker. Keep the paintball marker on SAFE until ready to shoot. Always remove gas source before disassembly. Fire only 0.68 caliber paintballs from this product. Read this manual and air system warnings before using this product. Any modifications or tempering of original factory parts will void all warranties and liabilities from Kingman. Always make certain the bolt is in the un-cocked position when marker is not in use. Always put marker on SAFE when marker is not in use. Transfer this instruction manual upon change of marker ownership.

N A M E O F PA R T S :

NAME OF PARTS:

MR2 Trigger Frame

8) Only use oil that is specifically designed for paintball markers. 9) It is a good practice to lubricate your marker before and after each use, especially when storing the marker for an

MR2 Touch Switch w/ Wire Harness

Blade Trigger

Trigger Set Screw

Trigger Pin

PRODUCT NAME/MODEL: W H AT OT H E R B R A N D ( S ) O F M A R K E R S D O YO U OW N ? :

extended period of time.

10) When you are finished shooting the marker, be sure to remove the Loader and all paintballs before storing. NOTE: there

W H Y D I D YO U P U R C H A S E T H I S K I N G M A N M A R K E R? :

may be a paintball in the breach of the marker, take a couple of shots in a safe direction to make sure that the Barrel and breach are empty.

11) Place the Barrel Plug into the Barrel to avoid accidental discharge of the marker. Turn the marker OFF and slowly

Ba r re l P l u g

Va l ve B o d y

Ve l o c i t y Ad j u st e r w/ S p r i n g G u i d e

ESP Sear Spring

unscrew the air source tank. Caution: do not remove the Tank Valve from the Tank, doing so may cause serious injury or

Va l ve B o d y Ro l l P i n

Ve l o c i t y Ad j u st e r O - r i n g

Touch Switch Roll Pins

Ba l l St o p p e r

Va l ve B o d y S c rew

M R 1 / M R 2 Q u i c k D i s co n n e c t P i n

Sear Roll Pin (Small)

M R 1 / M R 2 Fe e d N e c k

M R 1 / M R 2 M 4 x 8 S c rew w/ wa s h e r

St r i ke r S p r i n g

MR2 Circuit Board

M R 2 S h ro u d

M 5 x 1 2 S c rew w/wa s h e r

St r i ke r B u f fe r

Circuit Board Screw

M R 2 Re ce i ve r

M R 2 D e l r i n AC S B o l t

M R 2 S i g ht Ra i l

Coil Set

M R 2 Ve r t i ca l / C /A P l u g

St r i ke r B o l t

M R 2 S i d e P l at e ( Le f t )

Coil Set Screw

M R 2 Ve r t i ca l / C /A t o H o s e Ad a pt e r

St r i ke r O - R i n g

M R 2 S i d e P l at e ( R i g ht )

Battery Harness

M R 2 Re s e r vo i r Ad a pt e r P l u g

Ba r re l O - r i n g

M R 2 S n a p T- Kn o b

MR1/MR2 Shoulder Stock

M R 2 S h ro u d P l u g

MR2 Bolt Pin

M R 2 S n a p T- C l i p

Java 9.6v Rechargeable Battery

O-Ring #015 80D

M R 1 / M R 2 2 " D ove t a i l D ro p Fo r wa rd

M R 2 S n a p T-S p r i n g

A/C Charger - 110 v

Va l ve S p r i n g

D ro p Fo r wa rd Lo c k S c rew

M R 2 S n a p Ra i l Cove r

MR2 Parts Kit

Cu p S ea l G u i d e

M R 2 Fo re G r i p H a n d l e

Filter O-ring

Cu p S ea l

M R 1 / M R 2 St r i ke r P l u g

M a l e ST D / Fe m a l e M e t r i c

Air Filter

Va l ve P i n

M R 1 / M R 2 D ove t a i l B ot t o m - L i n e A S A

M R 2 G r i p Pa n e l s

Disconnect O-ring #011

12) Trigger Set Screws (#JE31L) have been positioned by the factory on the A and D setting. This is a factory setting that will minimize the trigger bounce. You can reposition the Trigger Screws (#JE31L) for your desired setting: A and C, A and D, B and C, or B and D. Important: You must use #242 Loc-Tite (blue color) every time the Trigger Set Screws are repositioned to prevent the loosening of Screws. Turn Trigger Screws 1 & 2 (#JE31J) clockwise or counter clockwise