Spyder Rsx Manual - English

CUP SEAL REMOVAL

REGULATOR MAINTENANCE / SCHEMATIC

MISC TROUBLESHOOTING / AIR LEAKS

WARRANTY STATEMENT

RSX PARTS LIST

RSX SCHEMATIC

IMPORTANT SAFETY GUIDELINES

OPERATION GUIDE / START UP WARNING: Always keep the marker powered OFF or on SAFE until you are ready to fire.

WARNING 1. 2. 3.

Treat every paintball marker as if it were loaded.

Never look down the barrel of a loaded or unloaded marker.

Always keep the paintball marker in SAFE or OFF mode until ready to operate.

Always attach a barrel blocking device over the tip of the barrel for safety precautions when the marker is not in use. Install and charge the battery see pages (see Battery Charging / Installation). Attach the Compressed Air Tank to the C/A On/Off adapter. HELPFUL TIP: Make sure to have the Compressed Air Tank filled before attaching to the marker. Tighten the Compressed Air Tank clockwise in the markers C/A On/Off adapter until it is snug. If an air leak occurs between the tank and the C/A On/Off adapter, replace the urethane bottle O-ring. NOTE: O-rings in the markers parts kit are not supplied to attach with a Compressed Air Tank. IMPORTANT: You should never need to use any hand tool to attach a Compressed Air Tank to the C/A On/Off adapter. 4. Attach an electronic loader on the Twist Clamp (#FND021) twist clockwise to fasten and counter clockwise to release the loader. Only use .68 caliber paintballs through the loader. NOTE: Kingman recommends that you use a force feed / high speed electronic loader to reach optimum performance. 5. Cocking the marker. Pull the Top Cocking Knob (#STK001) rearward until the Delrin bolt latches. CAUTION: Should you let go of the Top Cocking Knob before it latches, your marker may fire. 6. Remove the barrel blocking device. CAUTION: With the power switch turned ON the marker is LIVE. Pulling the trigger (#TRS005) will fire a paintball. IMPORTANT: Only test your marker in a safe direction or in a designated playing field. 7. Performing a velocity (fps) check. Turning the Velocity Adjuster / Spring Guide (#VTA021) clockwise will increase the velocity (fps) while turning counter-clockwise will decrease the velocity (fps). NOTE: This marker is equipped with a Regulator dial that can adjust the pressure from 0-600psi. (see Regulator Adjustment) NOTE: Your marker is intended to be used in a paintball facility with the proper paintball protection. IMPORTANT: Kingman recommends using a chronograph to ensure that the maker’s velocity is under 300 (fps). 8. When finished playing, remove all paintballs from the paintball loader before detaching from the markers feed neck. CAUTION: There may be a paintball in the marker’s breach; take a couple of shots in a safe direction to make sure the barrel and receiver are empty. 9. Place the barrel blocking device over the barrel tip. This will help avoid any accidental discharge. 10. Kingman recommends having the marker in the “SAFE or OFF” position after use. 11. Unscrew the Compressed Air Tank from the marker’s C/A On/Off adapter. Turning the tank counter-clockwise will detach it from the marker’s C/A On/Off adapter. CAUTION: Never expose any skin underneath the C/A On/Off adapters bleed hole when removing the tank. This can run the risk of getting skin burn from the releasing of the GAS. IMPORTANT: You should never need to use any hand tool to detach a Compressed Air Tank. 12. Store the marker in a paintball bag or in a safe place. WARNING: Before / after use of the marker, make sure to fasten all screws. Screws can become loose due to vibration. Loose screws can be dangerous and cause injury. HELPFUL TIP: It’s a good practice to lubricate your marker before and after each use, especially when storing the marker for an extended period of time. Add a few drops of paintball gun oil or marker grease on the Striker O-ring (#ORG001) (see Disassemble / Reassemble). Before storing the marker, make sure the marker is in the un-cocked position. This will help the main spring maintain its tension.

Always remove the gas source before disassembly.

IMPORTANT

Fire only 0.68 caliber paintballs with this product.

Always make certain the bolt is in the un-cocked position when marker is not in use.

This paintball marker is NOT a toy. It can cause serious injury or death.

Kingman recommends that the customer be at least 18 years of age to purchase this product.

Read this manual and air tank warnings before using this product.

Any modifications or tampering of original factory parts will void all warranties and liabilities from Kingman.

Kingman recommends using a barrel blocking device when the marker is not in operation.

• To ensure proper adjustment of velocity (fps), Kingman strongly recommends using a chronograph for paintball use located at most paintball stores and paintball fields. • Before / after use of the marker, make sure to fasten all screws. Screws may become loose due to vibration. Loose screws can be dangerous and cause injury. • Kingman STRONGLY recommends that any person using this product or within range of this product while it is in use MUST wear EYE/FACE PROTECTION designed specifically for the sport of paintball. This includes, but is not limited to, performing a maintenance check and during target practice. • Kingman reminds the user that it is YOUR RESPONSIBILITY to protect your eyes/face at all times, and will not be held liable for injuries sustained when failing to wear the appropriate protection. • Never shoot or point your marker at a person that is not in a designated paintball facility and without proper paintball protection.