Spyder Pilot Manual - English

WARNING

• Install a barrel plug in the barrel when not actually playing. • All persons using this product, or within range while this product is being used, must wear eye and face protection specifically designed for paintball. • Never shoot a person who is not wearing proper protection. • Treat every paintball marker as if it were loaded.

• VALVES MUST BE INSTALLED OR REMOVED ONLY BY QUALIFIED PERSONNEL.

• Never look down the barrel of the marker. • Keep the paintball marker on safe until ready to shoot.

• BOTTLE MUST BE RETESTED SEE CO2/HP TANK LABEL FOR RETEST DATE!

• Always remove gas source before disassembly. • Fire only 0.68 caliber paintballs from this product.

• Improper use, filling, storage or disposal of this cylinder may result in death, personal

• Read this manual and air system warning before using this product.

injury and property damage.

• Transfer this instruction manual upon change of marker ownership. • This cylinder must be filled only by properly Trained personnel in accordance with CGA Pamphlets P.1 and G-6.3 available from the Compressed Gas Association www.CGANET.COM

IMPORTANT

• Do not over pressurize. Do not expose pressurized cylinder to temperatures in excess of 130 degrees F.

• Firing velocity may vary according to altitude and climate conditions. • BEFORE using your marker in play, you must always first perform a

• Do not expose cylinder to corrosive materials and do not clean with caustic cleaners.

“SAFE VELOCITY TEST”. This can only be accomplished by using a testing device called a “Velocity Chronograph” and can be performed by the dealership where you

• Do not alter this cylinder in any way.

purchased this product or at a local paintball playing field. • NOTE: This product is intended to be used at a velocity no greater than

• Cylinders heated to a temperature of 250 degrees For more must be condemned or re-

300 feet per second (FPS).

qualified in accordance with test defined in CFR-49.

• Recommended velocity is 280 FPS or less. • This product is NOT intended to be used at any distance less than 25 feet.

• Keep cylinder out of reach of children.

• This paintball marker may have excess gas after removal of the tank. Please remove all paintballs and discharge the remaining gas safely.

• The valve should NEVER be detached from the canister. Should this occur, please seek assistance from a trained airsmith immediately. • This tank is intended for paintball use only.

Spyder Pilot NAME OF PARTS

NAME OF PARTS

Spyder Barrel Plug

C/A Adapter (Sky Blue)

12" Barrel (Silver)

Expansion Chamber Lock Screw

Ball Stopper w/ Detent Cover (Silver)

Deluxe Drop Forward (Silver)

M4 x 6 Screw (Silver)

Direct Feed (Silver)

5/32" x 7/8" Screw (Black)

Receiver (Sky Blue)

Filter O-Ring

M5 x 14 Screw w/ Washer

Air Filter

Vertical Adapter (Sky Blue)

Disconnect O-Ring #011

Low Pressure Chamber (Sky Blue)

Plastic Washer

O-Ring #015 80D

Disconnect Hose

Valve Spring

Spare Parts Kit

Cup Seal Guide

90 Male to Male Adapter

Cup Seal

Expansion Chamber (Sky Blue)

Valve Pin

Mini Fore Grip (Sky Blue)

Valve Body

Trigger Roll Pin

Valve Body Screw

Touch Switch Roll Pin

Frame Screw M5 x 12 Screw

On/Off Switch with wiring harnesses

Venturi Cocking Bolt

Battery harness

Retaining Screw

C.A.M.D Circuit Board

Retaining Spring

On/Off Screw (M2 x 6 Screw)

Retaining Bearing

Java 9.6v Rechargeable Battery

Striker O-Ring

Trigger Sear

Barrel O-Ring

Striker Bolt

Bolt Pin

Coil Set

Bolt Screw

Coil Set Screw

Quick Disconnect Pin

Charge Pin

Disconnect Pin Lock

Touch Switch

Striker Bolt Plug (Silver)

IPI-Tack Switch

Striker Spring

Circuit Board Screw

Striker Buffer

Tournament Lock Switch

Striker Spring Guide

Trigger

Flat Disc

Trigger Adjust Screw

Thumb Adjuster w/ screw (Sky Blue)

Sear Spring

Lock Screw

Trigger Spring

Rubber Grip Panel (Black)

Grip Cover Screws (M3 x 10)

Nut Screw

JE29 E29F JE26

E MARKER

SPYDER Pilot Parts List

37D 49B JE31C JE27 JE31F 49C JE18C