Spyder New Imagine Manual - English

WARNING

• Install a barrel plug in the barrel when not actually playing. • All persons using this product, or within range while this product is being used, must wear eye and face protection specifically designed for paintball. • Never shoot a person who is not wearing proper protection. • Treat every paintball marker as if it were loaded.

• VALVES MUST BE INSTALLED OR REMOVED ONLY BY QUALIFIED PERSONNEL.

• Never look down the barrel of the marker. • Keep the paintball marker on safe until ready to shoot.

• BOTTLE MUST BE RETESTED SEE CO2/HP TANK LABEL FOR RETEST DATE!

• Always remove gas source before disassembly. • Fire only 0.68 caliber paintballs from this product.

• Improper use, filling, storage or disposal of this cylinder may result in death, personal

• Read this manual and air system warning before using this product.

injury and property damage.

• Transfer this instruction manual upon change of marker ownership. • This cylinder must be filled only by properly Trained personnel in accordance with CGA Pamphlets P.1 and G-6.3 available from the Compressed Gas Association www.CGANET.COM

IMPORTANT

• Do not over pressurize. Do not expose pressurized cylinder to temperatures in excess of 130 degrees F.

• Firing velocity may vary according to altitude and climate conditions. • BEFORE using your marker in play, you must always first perform a

• Do not expose cylinder to corrosive materials and do not clean with caustic cleaners.

“SAFE VELOCITY TEST”. This can only be accomplished by using a testing device called a “Velocity Chronograph” and can be performed by the dealership where you

• Do not alter this cylinder in any way.

purchased this product or at a local paintball playing field. • NOTE: This product is intended to be used at a velocity no greater than

• Cylinders heated to a temperature of 250 degrees For more must be condemned or re-

300 feet per second (FPS).

qualified in accordance with test defined in CFR-49.

• Recommended velocity is 280 FPS or less. • This product is NOT intended to be used at any distance less than 25 feet.

• Keep cylinder out of reach of children.

• This paintball marker may have excess gas after removal of the tank. Please remove all paintballs and discharge the remaining gas safely.

• The valve should NEVER be detached from the canister. Should this occur, please seek assistance from a trained airsmith immediately. • This tank is intended for paintball use only.

Spyder Imagine (green and grey blue)

Coil Set Screw (A)

Low Pressure Chamber (Silver)

Charge Pin

Striker Plug (Silver)

IPI 3.0 Circuit Board

Rubber Grip Panel (Black)

Circuit Board Screw

Rubber Grip Panel (Grey)

Tournament Lock Switch

C/A Adapter (Green)

Trigger

C/A Adapter (Grey Blue)

Trigger Adjust Screw

Mini Fore Grip (Green)

Sear Spring

Mini Fore Grip (Grey Blue)

Trigger Spring

Expansion Chamber (Green)

Grip Cover Screw (Black)

Expansion Chamber (Grey Blue)

Grip Cover Screw (Silver)

Striker Spring

SPYDER Imagine Parts List

Vertical Adapter (Grey Blue)

Coil Set

Striker Bolt

Vertical Adapter (Green)

Imagine Receiver (Grey Blue)

Trigger Sear

Imagine Receiver (Green)

Java 9.6v Rechargeable Battery

Direct Feed (Grey Blue)

Straight Elbow - 2 3/4" (Clear)

On/Off Screw (M2 x 6 Screw)

Direct Feed (Green)

Disconnect Pin Lock

Battery harness

Quick Disconnect Pin

On/Off Switch with Wiring Harnesses

Bolt Screw

Touch Switch Roll Pin

Trigger Roll Pin

Bolt Pin

Barrel O-Ring (Black)

Male To Male Metric Adapter

Striker O-Ring

Imagine Spare Parts Kit

Disconnect Hose

JE33C / JE33D

Imagine Venturi Cocking Bolt

M5 x 12 Screw

Plastic Washer

Valve Body Screw

Disconnect O-Ring #011 (Black)

E MARKER

Valve Body

Air Filter

Filter O-Ring

Valve Pin

Cup Seal

5/32" X 7/8" Screw (Black)

Cup Seal Guide

Compact Nut Screw

Valve Spring

Thumb Adjuster w/ Screw (Grey Blue)

Thumb Adjuster w/ Screw (Green)

O-Ring #015 80D

M5 X 14 Screw w/ Washer

JE31F 49C JE18C JE30B

Lock Screw

Direct Feed Screw (silver)

Flat Disc

Striker Spring Guide

Ball Stopper w/ Detent Cover (Black)

9 1/2" Barrel (silver)

Striker Buffer

NAME OF PART (S)

Spyder Barrel Plug