RAIDER
HIGH PERFORMANCE PAINTBALL MARKER
USER MANUAL
This is not a toy. Misuse may cause serious injury or death. Eye protection designed specifically for paintball must be worn by the user and persons within range. Recommend 18 years of age or older to purchase. Persons under 18 years of age must have adult supervision. READ THIS MANUAL BEFORE USING.
READ OWNER’S MANUAL BEFORE USING. Rules of Safe Marker Handling 1. Treat every marker as if it were loaded. 2. N ever look down the barrel of a paintball marker. 3. Keep your finger off the trigger until ready to shoot. 4. Never point the marker at anything you don’t wish to shoot. 5. Keep the marker on “SAFE” until ready to shoot. 6. Keep the barrel blocking device in/ on the marker’s muzzle when not shooting. 7. Always remove paintballs and propellant source before disassembly. 8. After removing propellant source, point marker in safe direction and discharge until marker is degassed. 9. Store the marker unloaded and degassed in a secure place. 10. F ollow warnings listed on propellant source for handling and storage. 11. D o not shoot at fragile objects such as windows. 12. E very person within range must wear eye, face and ear protection designed specifically to stop paintballs and meeting ASTM standard F1776. 13. A lways measure your marker’s velocity before playing paintball and never shoot at velocities in excess of 91.44 meters (300 feet-per-second).
NOTE: Eye protective devices designed specifically for paintball use must be worn by the operator and anyone within range.
Barrel Installation 1. Make sure marker is degassed, hopper removed, no paintballs in the feed port or breech and the safety is set to “SAFE”. 2. While pointing marker in a safe direction, place the threaded end of the barrel into the front opening of the marker body. (Fig. 1) 3. Turn the barrel clockwise until it stops (do not over tighten). 4. A djust the barrel accessories if necessary. 5. Install a barrel blocking device. This can be a barrel plug or other such device that prevents the accidental discharge of a paintball.
Air Cylinder Installation
the barrel blocking device. 3. Point the Raider™ over a chronograph that will measure the velocity of the paintballs discharged by the marker. 4. Set the trigger safety to “FIRE” (red mark will show). (Fig. 2) 5. Pull the trigger and check the reading on the chronograph. 6. Locate the velocity adjuster screw on the center of Raider™, under the name plate. (Fig. 5) 7. Using a 5/32" hex key, turn the screw inward or clockwise to reduce the velocity, and outward or counterclockwise to increase the velocity of the paintballs discharged from the marker.
Loader Installation 1. Press the loader into the opening of the elbow until it stops. 2. Align the loader so that the lid is pointing to the rear and the loader is parallel with the marker.
(MARKER MUST BE UNLOADED, DEGASSED AND UNCOCKED BEFORE ANY DISASSEMBLY. FOLLOW UNLOADING AND REMOVING AIR SUPPLY STEPS.)
Removing the Barrel Turn the barrel counter clockwise to remove from the marker.
Disassembly beyond this point should only be done by trained personnel.
Elbow Removal/Reinstallation
Reassembly
Locate feedneck along the top rail near the front of the marker. With the marker laying flat (name plate on table) using a 1/8" Allen key, remove the bolts. Once bolts are removed you are free to slowly pull the feedneck halves apart. To reinstall, reverse the process.
To reassemble the marker, reverse the Disassembly instructions starting with the barrel adapter, ball retainer and bolt removal. While reassembling the marker, you should oil all O-rings and sliding parts. All parts and o-rings returned to the marker should be free of debris and visual nicks and scratches which can alter the performance of the marker. All screws returned to the marker must be tightened so there is no chance of them vibrating loose.
Proper Storage of the Marker
SAFETY ON
Fig. 3 3. Release the cocking knob. 4. The marker is now cocked. 5. Locate the air cylinder adapter. The Raider™ cylinder adapter is located at the base of the pistol grip. (Fig. 4) 6. Position the Raider™ so that the air cylinder adapter is pointed upwards while keeping the muzzle of the marker pointed in a safe direction.
When you are finished using the Raider™ it is important that you prepare the marker for storage. This will not only serve to increase the life of the marker, but will assure optimum performance on your next outing.
Limited Warranty
JT SPORTS warrants the replacement of any original part due to defect in material and/or workmanship of this marker. This warranty will be in effect for twelve (12) months for parts and twelve (12) months for labor following the original date of purchase for the original purchaser. Such warranty service will be provided only if the warranty registration card included with this manual is filled in completely and on file at JT SPORTSAll other service will be duly charged for and returned via UPS C.O.D.
Unloading 1. Make sure the barrel blocking device is properly installed and the marker safety is set to “SAFE”. 2. Loosen the loader clamping screw. 3. While holding the paintball hopper in place, invert the marker so that the hopper is below the Raider™. 4. Remove the hopper and all paintballs. 5. While pointing the Raider™ in a safe direction, remove the barrel blocking device and set the safety to “FIRE”. 6. Keep the Raider™ pointed in a safe direction and pull the trigger several times to insure there are no balls remaining in the chamber or the barrel. 7. Properly re-install the barrel blocking device and set the safety on “SAFE”.
Accessing Internal Components 1. Remove the Feedneck (see above). 2. Remove the Cocking Handle Cover (rubber bonnet). 3. Lay on a flat surface with the name plate facing up.
The RaiderTM comes with a removable barrel system. This feature allows the user to select a barrel that is most suitable for the playing conditions.
The first 1010 words, extracted from the PDF. Read the full manual above, or download it.