default). To turn off, press and hold the power button until the LED turns off, then release. Every time the marker is turned on, the eyes are enabled. The marker can be turned off regardless of the state of the eyes. See “Battery Indicator” section for additional details.
Eye Operation and Logic The eyes are enabled when the marker is first turned on. The eyes can be toggled by using the eye button. Press and hold the eye button for 1 second and the LED will change colors to indicate the mode change.
Trauma DM6 Ultralite Board Instructions Features • • • • • •
The signature board of Baltimore Trauma Fully functional in the Dye DM6 and Ultralite Frame Based on the Musashi 7 software New model microcontroller runs at 8 Mhz, the fastest DM6 aftermarket solution available Enhanced power switching hardware for the solenoid is capable of pushing 10 amps, more than 3 times the capability of the stock board Includes twelve (12) fire modes: uncapped semi-auto, capped semi-auto, PSP auto-response, PSP mild ramping, PSP max ramping, PSP z-burst, NXL fullautomatic, auto-response, mild ramping, max ramping, z-burst, and fullautomatic Asynchronously monitors the trigger switch using an interrupt based scan at 2 million times per second, faster than any other aftermarket board or chip for the DM6 Gangster setting allows 3 different options for every fire mode, giving 36 different “breakout” style modes Adjustable ABS programming prevents first shot drop-off AMB (anti-mechanical bounce) and CPF (cycle percentage filter) algorithms help to eliminate mechanical bounce and switch bounce Power efficient software and hardware lengthens battery life Programming mode allows changes to debounce, dwell, loader delay, AMB, ABS dwell, fire mode, fire mode max rate of fire, eye mode, CPF, ramp start, gangster mode, and LED colors All settings are stored in non-volatile memory so they are not lost when battery is disconnected One-touch startup enables the marker to fire instantly Automatic 15-minute idle power down saves batteries Three eye modes: delayed, forced with force shot, and test mode with rate of fire indicator Fully adjustable color schemes Low battery indicator hardware and software shows battery level each time the marker is turned on
Installation Removal and installation of the board on a DM6 must be carefully done to ensure the electronics are not damaged. Begin by removing the grips from the marker. This will expose the entire circuit board. Remove the two mounting screws, eye harness, and solenoid harness. Remove the stock board. Place the Trauma DM6 board in the grip frame and replace the two mounting screws. Plug in all the connections. If the marker will not turn on, it may be due to a low or incorrectly inserted battery.
LED Indicator The multi-color LED that shines out the left side of the grip panels shows which mode of operation the marker is currently in. The default color scheme is: Rapid Blinking Red Rapid Blinking Yellow Rapid Blinking Green Solid Blue Slow Blinking Blue Slow Blinking Yellow Slow Blinking Red
At startup this indicates an exhausted battery At startup this indicates a low battery At start this indicates a good battery Ball in breech, ready to fire No ball in breech Eye malfunction, max rate of fire reduced to 12.5 bps; clean eyes or make sure the gun is fired with paint and air Eyes disabled, rate of fire limited to 20 balls per second in mode 1; otherwise capped at fire mode max rate of fire for fire modes 2 – 12
Power Operation Pressing and releasing the power button turns the marker on. The battery indicator will show the current power level of your battery with a flickering red, yellow, or green LED. After, it will show a solid or blinking blue LED (unless changed from the
If used, the eye system cycles the marker as fast as possible. During each shot the eyes watch for the bolt to return, ending the current firing cycle and starting another as quickly as the pneumatics allow. If the eye system is continually blocked (e.g. putting your finger in front of the eyes) and is unable to see the bolt return after every shot, the max rate of fire will be reduced to about 12 balls per second to prevent further chopping, and the LED will blink the eye malfunction color (yellow by default). The only way to show the true speed of the Trauma DM6 board is to fire the marker with paint and air. When the eyes are off, the rate of fire is limited to 20 balls per second unless in fire mode 2-12, in which case the rate of fire is selected by the user. To determine if the eyes are working correctly, insert an object into the breech. Check to see if the LED changes from blinking blue to solid blue and then back to blinking blue (if using default colors) once the object is removed.
Battery Indicator Battery indicator software and hardware are standard on the Trauma DM6 board. When the marker is turned on, the LED will briefly flicker red, yellow, or green to indicate the status of your battery. If it flickers red, the battery is exhausted and should be changed as soon as possible. If it flickers yellow, the battery may last for another case of paint, but it is close to failing.
Programming The tournament lock must be disabled in order to change settings on the board. Pushing the small switch to the left of the battery terminals toggles the tournament lock. While the marker is turned off, push and hold the lock button. The LED will flash red or green to indicate the status of the lock. Red means the lock is on, while green means the lock is off. While the lock and the marker are off, pull and hold the trigger, then push the power button. The marker will boot into programming mode, showing a rainbow sequence before stopping at solid green. Pulling and releasing the trigger quickly will toggle between the different programming modes: Green Purple Yellow Blue Red White Teal Flickering Green Flickering Purple Flickering Yellow Flickering Blue Flickering Red Flickering White Flickering Teal
The first 1029 words, extracted from the PDF. Read the full manual above, or download it.