WARNING
Read and follow carefully the instructions and warnings contained in this manual. Failure to observe all instructions and warnings could lead to severe or permanent injuries. Note: This vision system cannot offer protection in all situations. ALWAYS wear your vision system when you are within or near an area where paintball markers are in use or when handling a paintball marker. NEVER remove or raise up your vision system in the playing area, even when lens gets dirty or fogs up. Should your vision system accidentally come off, protect your eyes immediately by getting to the ground, and covering yoru face with your hands. Inform all players to cease firing and request that a player or referee help you leave the playing area with your eyes covered. BEFORE the start of each game, all paintball markers must be chronographed ensuring that paintball speeds do not exceed 300 fps (91 m/s). Higher muzzle speeds can exceed resistance limits of the vision system, and can lead to serious or permanent injury. Do not play when paintball speeds are unverified or exceed recommended limits. GOGGLES ARE FOR PAINTBALL ACTIVITIES ONLY AND NOT FOR INDUSTRIAL USE.
USAGE AND CARE INSTRUCTIONS MANUAL
Before beginning a game test the Anti-Fog of your vision system’s lens by breathing on it’s inside surface. Should the lens fog up, treat with an approved anti-fog product or replace your lens.
DO NOT USE UNTIL ALL INSTRUCTIONS REGARDING SAFETY HAVE BEEN READ.
VISION SYSTEM AND LENS CARE
STORING YOUR VISION SYSTEM
Your G.I. VISION system uses a polycarbonate lens which is treated with a Thermo-Cured, Anti-Fog and Anti-Scratch coating ensuring the very best performance and clarity.
Make sure your G.I. VISION system is totally clean before storing it. Protect the lens from any possible impact or scratching. Always strore your vision system in a clean cool dry place. Protect from high temperatures, fumes, chemical products and abrasive materials.
CLEANING YOUR VISION SYSTEM Always clean your lens within 2 hours of any contact with paintball markings. Remove lens to thoroughly clean all vision system surfaces. Use only warm water to clean the lens. Cleaning products may hinder and weaken lens. Replace lenses that come into contact with any chemicals or fumes. Use only clean soft cloths when cleaning lens. Avoid using other substances that can damage, scratch or dull your lens such as newpaper, paper towels, dish towels or clothing. When drying out your lens please note that the inside anti-fog will go through a tacky phase. This is normal and will stop once lens is completely dry. In order to clean this surface properly. It is recommended that you pat dry with a moist cloth and not wipe the inside as this will lead to streaking. V-Force is a brand of G.I. Sportz Direct, LLC. PATENT(S): See www.paintballsolutions.com/patents © 2019 G.I. Sportz. All rights reserved. This G.I. Sportz product is protected by one or more United States patents. G.I. Sportz Trademarks, Designs and Copyrights are protected by one or more United States patents and International Law. For more information contact G.I. Sportz at [email protected]
REMOVING YOUR LENS.
Always check lens before adn after using. Lens should be replaced after one year of use, even if it appears perfect. Replace immediately if any scrathces or cracks are apparent, or after andy direct paintball impact less than a distance of 10 feet (3 meters). Note: Though uncommon in some cases the vision system may cause skin irritations in persons that suffer from skin inflammations or allergies. Should any irritations occur discontinue use immediately and consult a physician.
Before wearing your vision system ensure that lens and clips are firmly locked in place. Do not modify your vision system in any way. Use only approved product accessories from G.I. VISION.
LENS REMOVAL 1
LENS INSTALLATION
Remove temple clip pulling from the angled narrow end.
Remove Locking Mechanism (inner clip) by flexing it’s tip outward and then pushing it forward towards lens.
Once both temple clips and Locking Mechanism Clips (inner clips) are removed carefully push lens sides and remove.
STRAP REPLACEMENT
After inserting lens attach temple clip to outer side of vision system.
While holding temple clip on the outside, slide in the Locking Mechanism Clip (inner clip) in fasten position.
Slide in Locking Mechanism Clip until it “clicks” securely into place. Repeat step on opposite side.
FITTING VISION SYSTEM Make sure that the strap is inserted properly in the provided slot area in the sides of the vision system and that it fits snug to your head. Adjust strap by sliding strap adjusters to fit your exact head size. The inner foam area around the lens should sit properly and comfortably around your eyes.
*NOTE: Locking Mechanism Clips are branded L for left side and R for right side.
NOT DESIGNED FOR CHILDREN 12 YEARS AND UNDER
G.I. SPORTZ INC. 2955 ADAMS CENTER ROAD, FORT WAYNE, IN 46803 / WWW.GISPORTZ.COM
IMPORTANT!
When cleaning or replacing head strap, push Locking Mechanism Clips (inner clips) towards the outside of vision system until “clicking” sound is heard to ensure your strap is safely scure.
NOT USE UNTIL ALL INSTRUCTIONS W A R N I N G DO REGARDING SAFETY HAVE BEEN READ.
G.I SPORTZ EUROPE LTD. ADRENALINE HOUSE BROOKLANDS PARK, FARNINGHAM ROAD CROWBOROUGH TN6 2JD, GREAT BRITAIN WWW.PAINTBALLSOLUTIONS.COM
Meets or exceeds International Standards for: CCQS Certification Services Limited Block 1 Blanchardstown Corporate Park, Ballycoolin Road, Blanchardstown, Dublin 15, D15 AKK1, Ireland. Notified Body: 2834
G.I.VISIONⓇ and SLEEKⓇ are Registered Trademarks
Extracted from the PDF. Read the full manual above, or download it.