WARNING
DO NOT USE UNTIL ALL INSTRUCTIONS REGARDING SAFETY HAVE BEEN READ.
Your ARMORTM mask Has a single pane plycarbonate lens that has been treated with a Thermo-Cured Anti-Fog coating. More information on the lens is provided in the next section of this manual.
Read and follow carefully the instructions and warnings contained in this manual. Failure to observe all instructions and warnings could lead to severe or permanent injuries. Remember that your mask cannot offer protection in all situations.
Your new ARMOR™ mask by VFORCE™ provides the best quality and comfort available. The lens design ensures distortion-free vision, enhancing your rapid target-acquistion effieciency and overall safety. The unique Quick-Change system allows you to remove the lens in seconds, for cleaning, so you are back in the game in seconds. Every VFORCE mask has been handcrafted from the finest materials modern technology can provide. We test and refine everything we make to ensure you get reliable performance from a quality product. TM
• ALWAYS wear your mask when you are within or near an area in which paintball markers are being used or when using or handling a paintball marker. • NEVER remove or lift your mask in the playing area, even if the lens fogs or gets dirty. If your mask accidentally comes off, throw yourself on the ground and protect your eyes. Tell the players to stop shooting and ask the referees or one of the other players to help you leave the area with your eyes covered.
• Before the beginning of the game, all paintball markers must be chronographhed to ensure that the speed of the paintballs does not exceed 300 f.p.s. (91 m/s). Higher speeds could exceed the resistance limits of your mask and lead to serious or permanent injury. Do not play if the speed of the paintballs exceeds 300 f.p.s., or if speed is not verified.
One size fits all - Fits adult size: S / M / L
LENS REMOVAL
• In rare cases, any mask may cause irritation and should not be worn by persons who are subject to dermatitis. Discontinue the use of the mask immediately in case of irritation and consult your physician.
The mask’s chin strap should be fastened and secured at all times during play. Simply adjust the chin strap so it rests comfortably against your chin, then fasten the srap buckles.
VISOR INSTALLATION
VForceTM offers 3 lens types with varied transmissions to provide optimum vision in various lighting conditions. The papillary distance is 64 mm. Please also note the markings on the mask.
Insert the new lens, making sure that the fastening tabs are fully and securely in place. Ensure that both upper positioning tabs are inserted ion their respective slots.
Insert the visor supports in the ventilation slots on top of the mask.
STORAGE • Ensure that your VForceTM mask is clean before storing it. Protect the lens against impacts and scratches. Store your mask in a cool, clean and dry place, far from chemical products or fumes and protected from high temperatures.
LENS INFORMATION
ANTI-FOG TREATMENT • Despite the longest lasting ThermoCuredTM Anti-Fog process available, over time the anit-fog process available, over time the anti-fog treatment may lose its effectiveness. When this happens, only use VForceTM Anti-Fog solution. Do not use any other products, since it could weaken or damage the lens.
No paintball mask can prevent fogging under all conditions. If your lens fogs up NEVER remove your mask in the playing area!
Use only VFORCETM approved lenses that have been designed for your mask.
Remove the fastening clip from the lens.
Before each game, breathe on the inside surface of the lens. If it fogs-up, before you use your mask: replace the lens or treat it with VForce anti-fog solution.
LENS INSTALLATION Pull the strap gently, by sliding your fingers over and behind the strap.
PROPER MASK FIT
• Always follow all safety rules regarding the game and the handling of paintball markers.
www.paintballsolutions.com
Check that the strap is inserted properly in the slots provided in the mask, and that it fits snugly around your head. Ensure that the foam around the lens sits closely around your eyes.
CCQS Certification Services Ltd. NB 2834 Block 1, Blanchardstown Corporate Park, Ballycoolin Road, Blanchardstown, Dublin, D15 AKK1, Ireland
This product meets ASTM standards F 1776
Proper Mask Fit Mask and Lens Care Lens Removal Lens Installation Visor Installation Chin Strap Installation Lens Information
• Always wear your mask with visor and chin strap securely attached as per instructions.
Meets or exceeds International Standards for:
CLEANING • Clean your lens within two hours of any contact with paintball fills or residues. Remove the lens from the mask to ensure that all surfaces of the lens and the mask are thoroughly cleaned with clean water. • Use only clean warm water to clean the lens. DO NOT USE any other products or cleaners, as they could contain substances that may damage or weaken the lens, or reduce the Anti-Fog effect. Change thte lens if it has come in contact with chemical products or fumes. • To dry the lens, simply air dry, or use a clean soft cloth or micro-fiber on the outside of the lens. DO NOT RUB THE INSIDE OF THE LENS. DO NOT USE substances that could scratch or dull the lens, like newspaper, paper towels or clothing. It is normal for the anti-fog coating on the inside surface to go through a tacky phase while drying. To dry this surface, blot with a soft clean cloth and let it dry. Do not rub the inside, as it will streak, and you will have to begin again.
TABLE OF CONTENTS
• Make sure the lens and the lens retention clips are firmly in place before wearing the mask.
GOGGLES ARE FOR PAINTBALL ACTIVITIES ONLY AND NOT FOR INDUSTRIAL USE.
Use and Care Instructions for Paintball Vision System
MASK AND LENS CARE
CONGRATULATIONS!
Lens Model
Light Transmission
Filter
Category Comments
Lens for all conditions.
Place the O-rings in the notches of the visor supports.
The first 1010 words, extracted from the PDF. Read the full manual above, or download it.