OPERATION INSTRUCTIONS (See Diagram B) Step 1. Battery Installation A. Using a standard Phillips screw driver, remove the 2 screws on the bottom of the loader and the 1 screw at the front of the loader.
go. (see diagram F) IR sensor (eyes) activation: When the IR sensors are blocked by a paintball the loader will go to idle mode. When paintballs are shot, the impeller will begin feeding paintballs. The loader will return to idle mode if no more paintballs are shot. Spring Lid
DIAGRAM E DIAGRAMME E
DIAGRAM A / DIAGRAMME A / DIAGRAMA A
Housing — Right
Flip Lid Pin
DIAGRAMA E
Housing — Left Pipe Light
FLIP LID
Button Ball Ramp Ball Guide
PEDESTAL
Impellor Top Raceway
FEEDNECK
OWNER’S MANUAL Eye Activated Force Feed Electronic Loader
This Manual Contains:
Capacity On / Off Action Feed Rate
MARKER
DIAGRAMA B
• Warranty Information • Maintenance Instructions
DIAGRAM B DIAGRAMME B
• Operating Instructions • Annotated Diagram
Eye Covers
B. Connect the two 9 volt batteries to the battery clips and then drop the batteries (clips up) into the cavities on the right and left of the on/off button. Carefully tuck the extra wires around the on / off switch so that it won’t get pinched when you put the loader back together again. Carefully put the top back onto the pedestal and screw the 3 Phillips screws back in. (see diagram B and C)
DIAGRAM C DIAGRAMME C DIAGRAMA C
SPECIFICATIONS
18 volts (requires two 9 volt batteries (not included) Approx. 200 paintballs (.68 cal) Four Eye™ Infra-red circuit Eye Activated Force Feed On marker feed, up to 20bps.
Low-Battery: The LED will turn solid red to indicate low battery voltage. The loader will function with low battery voltage but feed rate will not be at highest level.
Pedestal Circuit Board
Auto Anti Jam Function: When the impeller arm is stopped
Battery Clips
by a jam the servo will reverse and clear the impeller. The clearing of a jam may take more than one reversing of the servo. The LED will turn orange for a moment when a jam is sensed. If excessive reversing is accuring the user will need to inspect the paintballs to determine what is causing the jam and clear paintballs or foreign objects from the loader. If you encounter several jam conditions in a loader full of paintballs you probably need to be using fresher or better quality paintballs. Note: Paintballs exposed to high temperatures can adhere to each other and will not feed in any loader. Protect your paintballs from direct sunlight and high temperatures whenever possible.
Switch Battery & Cleaning instructions screws
STORAGE To extend product and battery life, always turn the power switch off, remove the batteries, and store away from extremes in temperature and humidity.
CAUTION: USE OF ELECTRONIC CIRCUIT BOARD OR SERVO MOTOR OTHER THAN THE ORIGINAL SUPPLIED COMPONENTS MAY VOID YOUR WARRANTY. CHECK WITH VIEWLOADER BEFORE INSTALLING REPLACEMENT COMPONENTS.
WARNING: NEVER SHOOT AT ANYONE WITHOUT PROPER PROTECTIVE EQUIPMENT FOR EYES, EARS, THROAT AND HEAD, WHICH MUST BE WORN AT ALL TIMES. EYE PROTECTION MUST BE DESIGNED SPECIFICALLY FOR PAINTBALL USE. FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS MAY RESULT IN BODILY INJURY INCLUDING BLINDNESS AND DEAFNESS.
DIAGRAM H DIAGRAMME H DIAGRAMA H
DIAGRAM F DIAGRAMME F ON / OFF SWITCH
DIAGRAMA F
Note: make sure the on/off button is pushed and kept outward during installation. (see diagram D) The VL Eye- Force loader is an eye activated force feed loader that delivers consistent feed rates up to 20 balls per second. The patented and patent pending technology that drives this loader brings force feed performance to the price point that used to be agitating technology only. This loader was designed to keep up with the fire rates of electronic multi mode markers.
DIAGRAM D DIAGRAMME D DIAGRAMA D
ON / OFF BUTTON
CLEANING
Call 800.755.5061 or visit our web site at www.viewloader.com/service if you should need an Illustrated Parts List.
(Diagram G) Light cleaning may be done by using a flexible/fuzzy tip squeegee or similar object such as a paper towel to clean broken paintballs from inside the loader of feed tube. If more thorough cleaning is necessary follow maintenance guide for disassembly and cleaning.
JT Sports LLC. 5818 El Camino Real Carlsbad, CA 92008, U.S.A. 800.755.5061 Fax 760.579.5901 www.viewloader.com
Pro Tip: If you ever need to clean your loader follow the same steps
1. Always wear proper eye, face and ear protection designed especially to stop paintballs. 2. Never shoot a person who is not wearing proper protection. 3. Treat every paintball marker as if it were loaded. 4. Never look down the barrel of the marker. 5. Never point the paintball marker at anything you don’t wish to shoot. 6. Keep the paintball marker on safe until ready to shoot. 7. Keep the barrel plug in the paintball marker’s muzzle when not shooting. 8. Always remove gas source before disassembly. 9. Store the paintball marker unloaded and degassed in a locked place. 10. Follow warnings listed on gas source for handling and storage. 11. Never use anything other than .68 caliber paintballs. 12. Do not shoot fragile objects such as windows. 13. Paintballs may cause staining of some porous surfaces such as brick, stucco and wood. 14. Always measure velocity (speed of the paintball before it exits the barrel) before playing paintball. 15. Never shoot at velocities in excess of 300 feet per second. 16. Never engage in vandalism. 17. Do not use marker for drive-by shootings. 18. Do not modify your marker’s pressurized air system or cylinder in any way. P/N142518-000
as the battery installation instructions.
Step 2. Install Loader Press the neck portion of the loader into the feedport or elbow of the paintball marker as shown in direction of arrow and orient so the lid is to the rear of the marker. The neck is designed to fit most common paintball markers. The fit should be firm and tight. (see diagram E)
Step 2. Remove impeller top and arms from base. Clean and lubricate spring with white grease.
BATTLE SWAB
The first 1017 words, extracted from the PDF. Read the full manual above, or download it.