OPERATION INSTRUCTIONS
Quick start. Remove the two pins from the shell. Make sure the batteries are in correct orientation, Install into battery holder with positive terminal down. Check the placement of the ball tray between the tabs. Replaced the shell and pins. Press on/off button, the green LEDs flash to show battery volts. Assemble to marker with barrel blocking device installed. Just add paint and you are ready to play.
DIAGRAM A DIAGRAMME A
DIAGRAM D DIAGRAMME D
SHELL UPPER COQUE Supérieure CARCAS SUPERIOR
DIAGRAMA D
SHELL LOWER COQUE Inférieure CARCASA INFERIOR
FEEDNECK GOULOT D’ALIMENTATION
DIAGRAMA A
MARKER MARQUEUR
CAUTION: Do not overfill the loader! This will cause impeller jams or performance loss and could cause damage to the loader. Step 3. Load Paintballs: Open the spring loaded lid, load paintballs leaving some room for movement. Close the lid by pressing forward until lid latches (snap shut).
Step 4. Switch on Power: The on/off button is located at the back of the loader under the LED lights. When paintballs are loaded push this button once to turn your Evlution 4 loader on. Note: When you first turn the loader on there will be a slight pause. As the electronics calibrate the LED will begin to flash green at this time to show battery volts. Nine volts indicates full charge. Note: Each battery had its own LED indicator. (see diagram F)
(See Diagram A)
Disassemble To clean loader and ball tray remove the two pins from the shell. Separate the upper and lower shell. Then remove ball tray from upper shell by bending flexible tray towards you on one side and away from you on the other. (see diagram B) Once the ball tray is released pull out of the shell. To reassemble use same steps in reverse of above. Note: the bottom of the ball tray is marked with the word “Lid”. This end goes under the battery holder in the upper shell.
DIAGRAM F DIAGRAMME F DIAGRAMA F
When Both Red LEDs Are on Replace Batteries.
DIAGRAM B DIAGRAMME B DIAGRAMA B
Trademark Design Reg. No. 3,263,489
This Manual Contains: • Warranty Information • Maintenance Instructions
Capacity On / Off Action Feed Rate
• Operating Instructions • Annotated Diagram GREEN/RED LEDS DEL VERT/ROUGE LED VERDE/ROJO
SPECIFICATIONS
18 volts (requires two 9 volt batteries (not included) Approx. 195 paintballs (.68 cal) Four Eye™ Infra-red circuit Eye Activated Force Feed On marker feed, up to 18 bps.
WARNING: NEVER SHOOT AT ANYONE WITHOUT PROPER PROTECTIVE EQUIPMENT FOR EYES, EARS, THROAT AND HEAD, WHICH MUST BE WORN AT ALL TIMES. EYE PROTECTION MUST BE DESIGNED SPECIFICALLY FOR PAINTBALL. FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS MAY RESULT IN BODILY INJURY INCLUDING BLINDNESS AND DEAFNESS.
Flexible ball tray installation- The ball tray is inserted in the upper shell when disassembled. There are 5 sets of location tabs. The ball tray can flex and bend to pass over the batteries retaining shelf. Note: the bottom of the tray is marked with “LID” this should be facing you and placed toward the lid opening. To position the ball tray between the tabs reach in through the lid. Make sure the ball tray is centered between all 5 sets of tabs before installing the upper shell to the lower shell. Incorrect installation can lead to unnecessary jams when the hard part of the ball tray does not contact the raceway completely. SCALE
The VL Evlution 4 loader is an eye activated force feed loader that delivers consistent feed rates up to 18 balls per second. The patented and patent pending technology that drives this loader brings force feed performance to the price point that used to be agitating technology only. This loader was designed to keep up with the fire rates of electronic multi mode markers.
Call 800.755.5061 or visit our web site at www.viewloader.com/service if you should need an Illustrated Parts List.
DIAGRAM C DIAGRAMME C DIAGRAMA C
JT Sports LLC. 1201 S.E. 30th St., Bentonville, AR 72712, U.S.A. Fax (479) 464-8701 www.viewloader.com
RULES OF SAFE PAINTBALL MARKER HANDLING 1. Always wear proper eye, face and ear protection designed specifically for paintballs. 2. Never shoot a person who is not wearing proper protection. 3. Treat every paintball marker as if it were loaded. 4. Never look down the barrel of the marker. 5. Never point the paintball marker at anything you don’t wish to shoot. 6. Keep the paintball marker on safe until ready to shoot. 7. Keep the barrel plug in the paintball marker’s muzzle when not shooting. 8. Always remove gas source before disassembly. 9. Store the paintball marker unloaded and degassed in a locked place. 10. Follow warnings listed on gas source for handling and storage. 11. Never use anything other than .68 caliber paintballs. 12. Do not shoot fragile objects such as windows. 13. Paintballs may cause staining of some porous surfaces such as brick, stucco and wood. 14. Always measure velocity (speed of the paintball before it exits the barrel) before playing paintball. 15. Never shoot at velocities in excess of 300 feet per second. 16. Never engage in vandalism. 17. Do not use marker for drive-by shootings. 18. Do not modify your marker’s pressurized air system or cylinder in any way. P/N 143492-000 11/09
BUTTON BOUTON BOTóN
Intelligent Battery Managment Green LED voltage indicator: Each time you turn on the loader the microprocessor will test the battery voltage. The green LED will blink from 2-9 times. (see diagram F) This shows you exactly how many volts you have in each battery. You can perform a battery check at any time by turning the loader off and on. Your batteries should stay within one volt of each other during use. If you use rechargeable batteries or low cost batteries you may notice one battery running down quickly. You should not continue to use a rechargeable battery that runs down quickly. Low cost batteries generally have a shorter life than premium batteries. Low-Battery LED: When the loader is on but not feeding paintballs the LED will turn red to indicate low battery voltage. (see diagram F) You can…
The first 1016 words, extracted from the PDF. Read the full manual above, or download it.