Viewloader VL Force Loader Manual - English

OWNER’S MANUAL Eye Activated Force Feed Electronic Loader

• Warranty Information • Maintenance Instructions

Power Capacity On / Off Action Feed Rate

Pro Tip:

DIAGRAMA B

This Manual Contains: • Operating Instructions • Annotated Diagram

B. Connect the 9 volt battery to the battery clip and then drop the battery (clip up) into the cavities on the left of the on/off button. Carefully tuck the extra wires around the on / off switch so that it won’t get pinched when you put the loader back together again. Carefully put the top back onto the pedestal and screw the 3 Phillips screws back in. (see diagram B & C)

DIAGRAM C DIAGRAMME C

STORAGE To extend product and battery life, always turn the power switch off, remove the batteries, and store away from extremes in temperature and humidity.

Pedestal

CAUTION: USE OF ELECTRONIC CIRCUIT BOARD OR SERVO MOTOR OTHER THAN THE ORIGINAL SUPPLIED COMPONENTS MAY VOID YOUR WARRANTY. CHECK WITH VIEWLOADER BEFORE INSTALLING REPLACEMENT COMPONENTS.

Switch Battery & Cleaning instructions screws

DIAGRAM F DIAGRAMME F

DIAGRAMA C

SPECIFICATIONS

Raceway

If you are playing in the woods in a more hide and seek fashion you may want to keep the loader off until you engage your opponent. If you are playing speed ball in a closed in area you may want to keep the loader on for the full length of the game.

DIAGRAM B DIAGRAMME B

9 volts (requires one 9 volt battery (not included) Approx. 200 paintballs (.68 cal) One touch operation Continuous Force Feed On marker feed, up to 18bps.

DIAGRAMA F

SWITCH WARNING: NEVER SHOOT AT ANYONE WITHOUT PROPER PROTECTIVE EQUIPMENT FOR EYES, EARS, THROAT AND HEAD, WHICH MUST BE WORN AT ALL TIMES. EYE PROTECTION MUST BE DESIGNED SPECIFICALLY FOR PAINTBALL USE. FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS MAY RESULT IN BODILY INJURY INCLUDING BLINDNESS AND DEAFNESS.

WARRANTY INFORMATION GUARDRAILS

ON / OFF SWITCH

CLEANING Note: make sure the on/off button is pushed and kept outward during The VL Force loader is a continuous force feed loader that delivers consistent feed rates up to 18 balls per second. The patented and patent pending technology that drives this loader brings force feed performance to the price point that used to be agitating technology. This loader was designed to keep up with the fire rates of electronic multi mode markers.

installation. (see diagram D)

DIAGRAM D DIAGRAMME D

(Diagram G) Light cleaning may be done by using a flexible/fuzzy tip squeegee or similar object such as a paper towel to clean broken paintballs from inside the loader of feed tube. If more thorough cleaning is necessary follow maintenance guide for disassembly and cleaning.

ON / OFF BUTTON

Call 800-755-5061 or visit our web site at www.viewloader.com/service if you should need an Illustrated Parts List.

MAINTENANCE GUIDE

RULES OF SAFE PAINTBALL MARKER HANDLING 1. Always wear proper eye, face and ear protection designed especially to stop paintballs. 2. Never shoot a person who is not wearing proper protection. 3. Treat every paintball marker as if it were loaded. 4. Never look down the barrel of the marker. 5. Never point the paintball marker at anything you don’t wish to shoot. 6. Keep the paintball marker on safe until ready to shoot. 7. Keep the barrel plug in the paintball marker’s muzzle when not shooting. 8. Always remove gas source before disassembly. 9. Store the paintball marker unloaded and degassed in a locked place. 10. Follow warnings listed on gas source for handling and storage. 11. Never use anything other than .68 caliber paintballs. 12. Do not shoot fragile objects such as windows. 13. Paintballs may cause staining of some porous surfaces such as brick, stucco and wood. 14. Always measure velocity (speed of the paintball before it exits the barrel) before playing paintball. 15. Never shoot at velocities in excess of 300 feet per second. 16. Never engage in vandalism. 17. Do not use marker for drive-by shootings. 18. Do not modify your marker’s pressurized air system or cylinder in any way. P/N142534-000

FEEDNECK BATTLE SWAB

JT Sports LLC. 5818 El Camino Real Carlsbad, CA 92008, U.S.A. 800-755-5061 Fax 760-579-5901 www.viewloader.com

Pro Tip: If you ever need to clean your loader follow the same steps as the battery installation instructions.

Step 2. Install Loader Press the neck portion of the loader into the feedport or elbow of the paintball marker as shown in direction of arrow and orient so the lid is to the rear of the marker. The neck is designed to fit most common paintball markers. The fit should be firm and tight. (see diagram E)

CAUTION: Do not overfill the loader! This will cause impeller jams or performance loss and could cause damage to the loader. Step 3. Turning your loader on and off: The on/off button is located at the back of the loader. It is protected by “Guard Rails” that prevent accidental activation. Push this button once to turn your Force loader on. You will hear the motor and 6 blade paddle turning. The paddle will continue to turn until you push the button again and turn the loader off. (see diagram F) Note: LED Light is non functional in this model.

(ORIGINAL PURCHASE RECEIPT REQUIRED)

For 90 days from date of purchase, Viewloader® will repair or replace this loader free of charge if defective in material or workmanship. This warranty gives you specific legal rights. You may also have other rights which may vary from state to state. Service is available from authorized Viewloader® Service Centers. A list of these is available at Viewloaders’s website at www. viewloader.com or by calling Viewloader® at 800-755-5061. These Service Centers generally…