SHOCKER RSX
PLEASE READ CAREFULLY
OWNER’S MANUAL
WWW.SHOCKERPAINTBALL.COM
Q UI CK START
Velocity must be measured and adjusted to below 300 feet per PLEASE READ second (91.4 meters per second)CAREFULLY before each session of use.
01 INSTALL BATTERY
02 BARREL Use a 5/64-inch hex key to remove the three screws from the left side of the wrap-around grip and lift the left side open. Attach the battery clip to a new brand-name 9-volt alkaline battery and place it in the grip frame. Carefully tuck the battery wires out of the way of the grip. Close the grip and reinstall the grip screws.
STATISTICS
Assemble and install the included barrel. Make sure The Freak® insert is installed inside the barrel back. Install the assembled barrel in the front of the Shocker® RSX body. Take care not to cross-thread any barrel components during assembly or installation, as permanent damage may result.
03 BARREL BLOCKER & LOADER
Carefully screw a professionally filled paintball High Pressure Air (HPA) system into the Air Source Adapter (ASA).
Slide the included barrel blocker over the end of the Shocker® RSX barrel. Sling the blocker’s cords over the back of the marker and snug them tight.
Slowly turn the ASA knob clockwise to gently charge the Shocker® RSX with air.
The barrel blocker is a critical piece of safety equipment and must always be used when the Shocker® RSX is handled outside of an active paintball field.
Turn knob slowly! A quick pressure surge may cause damage.
The Shocker® RSX may be turned off by pressing and holding the power button until it goes dark. Turning off the Shocker RSX serves the same function as a mechanical trigger safety, but should not be relied on in place of a barrel blocker. ®
Table of contents
digital controls
Gasses
Programming
Electronic Settings
Firing Modes
Trigger Adjustment
Force Adjustment
Feedneck Adjustment
OPERATING PRESSURE: 170 psi POWER SOURCE:
9v Alkaline Battery
PROPELLANT:
High Pressure Air
OPERATION:
Electropneumatic
MODES OF FIRE:
ANTI CHOP SYSTEM:
Break Beam Vision
BARREL THREAD:
Autococker
LUBRICANT:
GR33SETM
Routine Maintenance Bolt / Valve ON
06 ADJUST VELOCITY Turn on the Shocker® RSX by pressing and holding the power button until it glows green and the RSX data display animates.
QUICK START - VELOCITY ADJUSTMENT
Adjustment/Tuning
TURN ON AIR
Install a high-performance paintball loader in the locking feedneck. In order to perform its at its best, the Shocker® RSX must be consistently fed unbroken paintballs rapidly.
TABLE OF CONT ENTS
Velocity must be tested and adjusted at the start of each paintball session. Fill the loader with paintballs and turn it on. While wearing ASTM compliant paintball goggles in an area where all bystanders are protected, remove the barrel blocker and fire over a chronograph to measure the velocity. Using a 5/32-inch hex key, turn velocity up (clockwise) or down (counterclockwise) as needed to meet the field’s standard. After each adjustment take 2 or three shots to allow pressure to stabilize, then fire over a chronograph to check velocity. For safety and to avoid internal damage, never adjust the Shocker® RSX to fire at greater than 300 feet per second.
Vision
/ Detents
Advanced Maintenance Regulator
Grip Frame
Bolt Control / Solenoid Valve / QEV 18 Troubleshooting
Parts Guide
WARRANTY / TECH SUPPORT
– THE SHOCKER® RSX IS NOT A TOY.
– MISUSE OF THE SHOCKER® RSX MAY RESULT IN SERIOUS INJURY OR DEATH.
– EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN BY THE USER AND ANY PERSON WITHIN RANGE OF THE SHOCKER® RSX. – SP RECOMMENDS THAT THE SHOCKER® RSX ONLY BE SOLD TO PERSONS 18 AND OLDER. – THOROUGHLY READ THE SHOCKER® RSX OPERATION AND INSTRUCTION MANUAL BEFORE OPERATING.
D IGITAL CON TROL S POWER The Shocker® RSX is turned on by pressing and holding the power button for a full second, or until the power button glows green and the data display activates [See FIG 07]. As soon as the Shocker® RSX is on, it is live and ready to fire. When the Shocker® RSX is in use, the power button may illuminate in different colors, or stop glowing to indicate various conditions. The Shocker® RSX is turned off by pressing and holding the power button for approximately two seconds. Turning the Shocker® RSX off is the equivalent to using a trigger “safety” switch on a mechanical paintball marker - while an important feature, it does not replace proper use of the barrel blocker. MODE The currently selected firing mode and its Rate of Fire Cap (ROFCap) are shown near the top of the data display. VISION� The status of the Vision™ anti-chop system is shown as a paintball in the middle of the display. A hollow paintball and blinking green power button indicates that the breech is empty. A solid paintball and solidly lit green power button indicates that the breech is full and ready to fire. If a problem is detected “EYE FAULT” will be displayed and the power button will blink red. Vision™ may be manually turned on or off by pressing the power button for one second. The power button will glow red and the display will read “EYEOFF” with an X in place of the paintball when Vision™ is off. When Vision™ is off or faulted, the Shocker® RSX will pause between shots to allow more time for the next paintball to settle in place. BATTERY Estimated battery charge level is indicated in the lower right of the display. Accuracy may vary between battery brands, especially when using rechargeable batteries.
07 RSX DATA DISPLAY
POWER BUTTON
REMOVE HPA SYSTEM 09
VISION STATUS MAX ROF
BATTERY LEVEL
Do not to unscrew HPA tank from its regulator!
GAME TIMER When enabled, the game timer is displayed in the bottom left of the display. The timer starts counting down when the first shot is fired. Turning the Shocker® RSX off and back on again will reset the timer.
GASSING The Shocker® RSX is equipped with a bottom-line style air source adapter (ASA). Before screwing an HPA system into the ASA, make sure the ASA is turned off by loosening the ASA knob on its front [FIG 8]. Take care not to turn the ASA knob too far. The pin inside the…
The first 1039 words, extracted from the PDF. Read the full manual above, or download it.