SHOCKER NXT Operation and adjustment instructions
Q U I C K START 01 BATTERY
The SHOCKER NXT can be damaged by liquid CO2. Thoroughly read and understand the Gasses Section of the manual before using CO2 to avoid damage.
02 BARREL BLOCKER Screw the included barrel into the Shocker NXT. Put the supplied barrel blocker over the end of the barrel, securing its cord as far back on the Shocker NXT body as possible, and cinching it tight.
Using a 5/64-inch Allen wrench, remove the two screws from the left side of the rubber grip, and lift the panel open. Attach a fresh 9-volt alkaline battery to the battery clip. Position the battery in the grip frame, tucking the battery wires into the space above the battery. Close the grip and reinstall the screws.
04 LOADER
03 FILL TANK
05 TURN ON AIR Insert your loader into the feedneck and make sure it is secure. Due to the high rates of fire that Shocker NXT can achieve, we recommend the use of a modern high-performance loader.
Have your compressed air (HPA) or CO2 tank filled by a person who is properly trained to do so. If using an HPA system with an on/off valve, such as the Max-Flo or Max-Flo Micro, make sure it is in the OFF position. If using a screw-in style preset HPA tank, or CO2 tank, an ASA with a built in on/off valve is recommended.
06 TURN ON SHOCKER Gently gas up the Shocker NXT by slowly turning on the air system or ASA’s on/off valve, or slowly screwing the CO2 or compressed air system into the ASA. A gentle rise in pressure is important, as a sudden blast may reduce the service life of the Shocker NXT’s internals.
Turn on the Shocker NXT by holding the power button down for approximately 1 second. The Shocker NXT will chirp and the power button will glow continuously to show that it is on and in Vision mode. If you need to disable Vision mode to fire gas without paint, push the button once again, and the power button will blink in a double-tap sequence. Press and hold the power button for approximately 2 seconds to turn the Shocker NXT off, this acts as an electronic safety.
07 ADJUST VELOCITY Fill the loader with paint and turn it on. While wearing ASTM compliant paintball goggles in an area where all bystanders are protected, remove the barrel blocker and fire over a chronograph to measure the velocity. Using a 3/32-inch Allen wrench, loosen the velocity lock screw near the bottom of the vertical regulator and adjust it with a 5/8-inch open-end wrench or adjustable wrench. Turn clockwise to increase velocity/pressure, and counter-clockwise to decrease. Take three or four shots after every adjustment to allow the gas pressure inside the Shocker NXT to stabilize. Adjust until the Shocker NXT is firing consistently within the limits for the field where you are playing (for safety reasons, never adjust the Shocker NXT to fire at greater than 300 feet per second.) As you adjust, check the Shocker NXT’s pressure gauge to be certain you stay within the Shocker NXT’s operating limits of 180 to 220 psi. Lock the velocity setting by tightening the velocity lock screw. Depending on what modes of fire are allowed at the field where you are playing (semi-automatic, rebound, etc.) you may need to adjust the Shocker NXT’s Rebound setting. See the Rebound Adjustment section for more information. Shoot out the competition, hang the
www.smartparts.com
TA B L E OF CONTENTS
SHOCKER NXT INSTRUCTION MANUAL
Quick Start
Getting Familiar
Gas System Mounting
Velocity
Vision
Rate of Fire
Rebound
Trigger
[ DISASSEMBLY/REASSEMBLY ]
Shocker NXT Parts Diagram
Degassing
Bolt and Valve [ DISASSEMBLY ]
Bolt and Valve [ CLEANING/REASSEMBLY ]
Regulator [ CLEANING/REASSEMBLY ]
Ball Detent/Vision Eye
Grip Frame Removal
Vision Eye Removal
Grip Frame [ REASSEMBLY ]
Troubleshooting
Warranty/Tech Support
– THE SHOCKER NXT IS NOT A TOY – MISUSE OF THE SHOCKER NXT MAY RESULT IN SERIOUS INJURY OR DEATH. – EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN BY THE USER AND ANY PERSON WITHIN RANGE OF THE SHOCKER NXT. – SMART PARTS RECOMMENDS THAT THE SHOCKER NXT ONLY BE SOLD TO PERSONS 18 AND OLDER. – THOROUGHLY READ THE SHOCKER NXT OPERATION AND INSTRUCTION MANUAL BEFORE OPERATING.
Extracted from the PDF. Read the full manual above, or download it.