The MINI GS uses .68 caliber, water-soluble paintballs, readily available at paintball pro-shops, commercial playing fields, and many sporting goods stores. The paintballs are fed from the loader through the direct vertical feed port and into the breech of the marker. FIRING THE MINI GS Keep your finger out of the Trigger Guard and away from the Trigger, point the barrel of your marker in a safe direction at all times during this process. Be sure your goggles are securely in place and make sure the MINI GS marker is OFF. This is not a toy. Misuse may cause serious injury or death. Eye protection designed specifically for paintball must be worn by the user and persons within range. Recommend 18 years of age or older to purchase. Persons under 18 years of age must have adult supervision. READ THIS MANUAL BEFORE USING. Read the full Operator’s Manual for technical information, usage instructions, and maintenance tips for your MINI GS marker. The full manual can be found at www.paintballsolutions.com or by contacting Paintball Solutions at 1-800-220-3222 or at 866-685-0030 in Canada. WARNING: Never carry your paintball marker uncased when not on a playing field. The non-playing public and law enforcement personnel may not be able to distinguish between a paintball marker and a firearm. For your own safety and to protect the image of the sport, always carry your marker in a suitable marker case or in the box in which it was shipped.
Treat every marker as if it were loaded. Never look down the barrel of a paintball marker. Keep the marker in “Safe Mode” until ready to shoot, power Off and barrel blocking device installed in/on the marker’s Barrel. Keep your finger off the Trigger until ready to shoot. Never point the marker at anything you don’t wish to shoot. Keep the barrel blocking device in/on the marker’s Barrel when not shooting. Always remove paintballs and the air source before disassembly. After removing the air source, point marker in safe direction and discharge until marker is degassed. Store the marker unloaded and degassed in a secure place. Follow warnings listed on the air source for handling and storage. Do not shoot at fragile objects such as windows. The operator and every person within range must wear eye, face and ear protection designed specifically to stop paintballs and meeting ASTM standard F1776. Always measure your marker’s velocity before playing paintball and never shoot at velocities in excess of 300 feet-per-second (91.44 meters-per-second). • Read this entire manual before loading, attaching a propellant source or in any way attempting to operate the Empire Mini GS marker. BARREL INSTALLATION - While pointing marker in a safe direction, place the threaded end of the barrel into the front opening of the marker body. - Turn the barrel clockwise until it stops (do not over tighten). - Install a barrel-blocking device which is included. This can be a barrel plug or other such device that prevents the accidental discharge of paintballs.
WARNING- Everyone within firing range should always use paintball approved eye and face protection in the presence of live paintball markers.
1. Place the empty loader onto the marker. 2. Be sure that it is securely mounted in place. 3. Apply the compressed gas, pressurizing the marker. 4. Put the paintballs into the loader. 5. Remove the barrel plug, sock or barrel-blocking device. 6. Aim the MINI GS in a safe direction. 7. Turn the MINI GS ON: Push the button for 2 seconds until the LED light changes to solid GREEN, then release button and LED should display a flashing LED according to Eye Status 8. Aim the MINI GS at the target. 9. Pull the Trigger with a smooth squeezing motion. REGULATOR ADJUSTMENT If adjustments are needed use a 3/32” hex wrench and insert it into the regulator adjustment screw. This is located in the front of the regulator. - To Increase pressure turn Clockwise. - To Decrease pressure turn Counter-clockwise. Notes: - Always watch the gauge as you are adjusting the pressure. - Do Not Use CO2! - The Bottomline Regulator should not be disassembled. - Never set the regulator above 210 psi.
ADJUSTING THE VELOCITY At the back of the MINI GS main Body is the Bolt Guide Cap. The hex screw in the Bolt Guide Cap serves as your velocity adjuster. Confirm that the pressure on your Bottomline Regulator is at or below 200 PSI. Then you can increase or decrease the velocity on your MINI GS by tightening or loosening the velocity adjustment screw with a 3/32” inch hex wrench. A paintball specific radar chronograph should be used to accurately measure your velocity. -To Increase Velocity Unscrew or loosen the velocity adjustment screw by turning it counterclockwise. Rotate the velocity adjustment screw counter-clockwise in small increments (1/4 turn or less), stopping between slight turns to test velocity, until desired velocity is achieved. Do not back the adjuster out past being flush. Stop if you hear an air leak, and adjust back in a 1/4 turn.
SWITCHING ON YOUR MINI GS - To switch the MINI GS On, locate the Power Button on the back side of the front Foregrip, in front of the Trigger guard and under the LED. - Push and hold the button for 2 seconds. The LED will glow solid RED as soon as the button is pressed. Continue to hold the button until the LED glows solid GREEN. - Release button and the LED will intermittently flash indicating that the marker is now ON and LIVE in FIRE Mode. - The LED color will be determined by the battery level, as listed in the chart described under the Battery Life Indicator section of this manual.
-To Decrease Velocity Tighten or screw-in the velocity adjustment screw by turning it Clockwise. Rotate the velocity adjustment screw Clockwise in small increments (1/4 turn or less), stopping between slight turns to test velocity, until desired velocity is achieved.
Note: Be sure not to have the Trigger pressed when turning the board on, as this will enter the board into Settings Mode.
The first 1016 words, extracted from the PDF. Read the full manual above, or download it.