Planet Eclipse EMC Etha 2 Rail Kit Manual - English

1X PAIR STOCK ADAPTOR (LARGE)

NOTE CONTENTS MAY VARY

1X PAIR STOCK ADAPTOR (SMALL)

2X 10-32 X 0.5” CAP HEAD SCREWS

16X 6-32 X 0.5” BUTTON HEAD SCREWS (2 SPARES)

2X 6-32 X 0.3125” COUNTER SUNK SCREWS

WARNING!

4X BARREL SHROUD RETAINING CLIP (2 SPARES)

2X 020 NBR70 O-RING (1 SPARE)

DE-GAS YOUR MARKER, DISCHARGING ANY STORED GAS IN A SAFE DIRECTION, AND REMOVE THE BARREL,LOADER,AIR SYSTEM AND ANY PAINTBALLS TO MAKE THE MARKER EASIER AND SAFER TO WORK ON. IMPROPER INSTALLATION, MISUSE, ILLEGAL USE OR MODIFICATION OF THIS PRODUCT OR ANY ATTACHED 3RD PARTY PRODUCTS MAY RESULT IN SERIOUS INJURY OR DEATH. MAKE SURE TO FULLY CLEAN ANY PAINT RESIDUE FROM YOUR RAIL KIT IMMEDIATELY AFTER USE TO AVOID POTENTIAL DAMAGE TO THE SURFACE FINISH.

IF YOU PLAN ON USING ANY 3RD PARTY BOLT ON RAIL SECTIONS IN THE 2, 3, 4 AND 8, 9, 10 CLOCK POSITIONS ON THE RAIL KIT, THESE NEED TO BE INSTALLED BEFORE ATTACHING THE ETHA2 EMC SHELLS.

1.0 - REMOVING THE ETHA2 METAL BODY

1.1 - UNSCREW AND REMOVE THE LEFT AND RIGHT

1.2 - UNSCREW AND REMOVE THE FEED TUBE USING A

1.3 - UNSCREW AND REMOVE THE FRAME USING A

BREECH SENSOR (BS) RETAINING SCREWS [K] AND

5/32” HEX KEY.

1/8” HEX KEY.

BS COVERS [C] USING A 5/64” HEX KEY. REMOVE THE

1.4 - TAKE CARE NOT TO DAMAGE ANY OF THE COMPONENTS ON TOP OF THE CIRCUIT BOARD.

RUBBER DETENTS [1] AND RETAIN FOR INSTALLATION.

1.5 - LOCATE THE LIP AREA ON THE GRN BODY AS

1.6 - PLACE BOTH THUMBS ON THE LIP.

1.7 - KEEP FINGERS & THUMBS AWAY FROM MOVING PARTS TO AVOID INJURY. FOLLOW THE CORRECT PROCEDURE AS SHOWN.

1.8 - YOU WILL NEED TO RETAIN OR INSERT YOUR

1.9 - PUSH DOWN WITH ENOUGH CONTROLLED FORCE

BARREL BACK SECTION AS IT WILL ASSIST YOU IN

TO RELEASE THE ETHA2 METAL BODY FROM THE GRN

FORCING OUT THE METAL BODY.

PLACE A TOWEL OR ADEQUATE PADDING ON THE FLOOR TO PROTECT YOUR BARREL FROM DAMAGE.

STOP PUSHING ONCE THE BODY IS RELEASED. FAILURE TO CONTROL THE RELEASE OF THE BODY COULD RESULT IN INJURY.

1.10 - SLIDE THE METAL BODY FROM THE GRN SHELL. AVOID INJURY SEE [1.7]

2.0 - INSTALLING THE ETHA2 EMC KIT

2.1 - PLACE THE METAL BODY [1] INTO THE LEFT OR

SCREW THE TWO SHELLS [A] TOGETHER WITH EIGHT

2.2 - ATTACH THE FRAME AND REPLACE THE TWO

2.3 - REPLACE THE RUBBER DETENTS [1] IN THE

RIGHT SHELL [A] ALIGNING THE FEED PORT WITH THE

OF THE 6-32 X 0.5” BUTTON HEAD SCREWS [I]

FRAME SCREWS. ENSURE THE SOLENOID GASKET IS

METAL BODY THEN INSTALL THE LEFT AND RIGHT BS

FEED BOSS IN THE SHELL.

PROVIDED USING A 5/64” HEX KEY.

SEATED CORRECTLY BEFORE REPLACING THE FRAME

COVERS [C] AND RETAINING SCREWS [K] USING A

SCREWS USING A 1/8” HEX KEY.

5/64” HEX KEY.

INSERT THE STOCK LOCKING TAB [D] INTO THE BACK OF THE SHELL. PLACE THE OTHER SHELL [A] OVER THE METAL BODY [1].

2.4 - INSTALL THE FEED TUBE ASSEMBLY USING A

2.5 - OPEN THE STOCK LOCKING TAB [D] USING A

2.6 - CLOSE THE STOCK LOCKING TAB [D] TO SECURE

2.7 - INSTALL A BARREL BACK AND BARREL TIP

FINGER OR SMALL HEX KEY.

THE ACCESSORY INTO PLACE.

ENSURING BOTH ARE SCREWED SECURELY INTO THE MARKER.

INSERT THE BLANKING PLUG [E], STOCK ADAPTOR [G/H] OR STOCK DROP INSERT [F] WITH COMPATIBLE STOCK* INTO THE BACK OF THE EMC KIT.

2.10 [OPTIONAL]

2.8 - SCREW THE TWO HALVES OF THE BARREL SHROUD [B] TOGETHER USING SIX 6-32 X 0.5” BUTTON HEAD SCREWS [I] PROVIDED USING A 5/64” HEX KEY.

2.9 - APPLY A SMALL QUANTITY OF GREASE TO THE RETAINING ARMS [1]. SLIDE THE SHROUD [B] OVER THE BARREL AND PUSH THE RETAINING ARMS [1]

2.10 (OPTIONAL) - THE SHROUD WILL BE SECURE

2.11 - TO REMOVE THE RETAINING CLIPS PULL THE

INSIDE THE MAIN SHELLS FOR MOST USERS WITHOUT

CLIPS OUT STRAGHT FROM THE BARREL SHROUD. DO

FURTHER RETENTION. FOR AN EXTRA SECURE FIT, PUSH

NOT PULL OR LEVER OFF AT AN ANGLE OR THE CLIPS

INTO THE ETHA2 EMC SHELLS [A].

THE RETAINING CLIPS [L] INTO THE SLOTS ON THE

MAY BE DAMAGED.

THE INSTALLATION OF THE BARREL SHROUD IS OPTIONAL. IT WILL NEED TO BE REMOVED BEFORE THE BARREL CAN BE REMOVED FROM THE MARKER.

ETHA2 EMC SHELLS. THE FRONT TWO SCREWS ON THE BARREL SHROUD AND ETHA2 EMC SHELLS MAY NEED LOOSENING SLIGHTLY, USING A 5/64” HEX KEY, IF THE BARREL SHROUD IS DIFFICULT TO INSTALL.

THE RETAINING CLIPS MUST BE PUSHED INTO THE SHELLS STRAIGHT, NOT AT AN ANGLE.

3.0 - STOCK INSTALLATION

3.1 - PLACE STOCK [1] INTO THE LEFT OR RIGHT STOCK

3.2 - PLACE THE STOCK ADAPTOR [G/H] HALVES

3.3 - INSERT THE ASSEMBLY INTO THE BACK OF THE

3.4 - THE STOCK ADAPTOR [G/H] COMPRISES OF A

DROP SHELL [F] PLACE THE REMAINING SHELL OVER

AROUND THE STOCK DROP [F] INSERT, FOLLOWED BY

ETHA2 EMC SHELLS AND CLOSE THE STOCK LOCKING

LEFT AND RIGHT HALF. FIT THEM TOGETHER WITH THE

THE STOCK.

THE RETAINING NBR70 O-RING [M].

LARGE 020 NBR70 O-RING [M] SAT IN THE STOCK ADAPTORS MIDDLE GROOVE. THE STOCK CAN NOW BE

SCREW TOGETHER WITH TWO 10-32 X 0.5” CAP HEAD SCREWS [J] PROVIDED USING A 5/32” HEX KEY.

THERE ARE TWO DIFFERENT SIZED ADAPTORS

FITTED TO THE EMC RAIL KIT.

PROVIDED WITH THE KIT. THE ADAPTORS WITH AN ADDITIONAL EXTERNAL GROOVE HAVE A SMALLER INTERNAL DIAMETER.

NOTE *THE ETHA2 EMC STOCK ADAPTOR ACCEPTS MOST BT-4TM/MODEL-98TM ADJUSTABLE CAR STYLE STOCKS. SOME 3RD PARTY BT-4TM/MODEL-98TM STYLE STOCKS MAY NOT FIT PERFECTLY IN THE EMC RAIL SYSTEM ADAPTOR AND SOME MODIFICATION MAY BE REQUIRED TO ACHIEVE A TIGHT FIT. WE SUGGEST USING A THIN LAYER OF ELECTRICAL TAPE OR SIMILAR ON THE GROOVED SECTION OF THE STOCK TO ENSURE A TIGHT FIT IN THE ADAPTOR.

3.5 - INSERT YOUR EMC COMPATIBLE STOCK*