APE Tippmann A5 Rampage Manual - English

PRODUCT WARRANTY

Advanced Paintball Electronics P.O Box 125 Odessa, Florida 33556-0125 [email protected] OR VISIT OUR FORUMS AT WWW.GOAPEONLINE.COM

A5 / PRO-E / BT

RAMPAGE™ USERS GUIDE

For technical support or help with your existing product, please contact WARNING - ALL PERSONS WITHIN RANGE OF A PAINTBALL MARKER MUST USE PROPER EYE PROTECTION. NEVER DISASSEMBLE A MARKER WHILE IT IS UNDER PRESSURE WITH COMPRESSED AIR OR CO2. ALWAYS REMOVE THE AIR SOURCE BEFORE WORKING ON YOUR MARKER. ALWAYS FOLLOW THE MANUFACTURER’S INSTRUCTIONS WHEN USING OR WORKING ON YOUR MARKER. NOT FOLLOWING PROPER INSTRUCTION MAY CAUSE PERSONAL INJURY AND/OR POSSIBLE DAMAGE TO YOUR MARKER. USE THIS PRODUCT AT YOUR OWN RISK.

USING YOUR NEW RAMPAGE™ BOARD The Rampage™ board is a high-performance upgrade for your marker. We recommend using a fresh battery before any major tournament or event to ensure peak performance. QUICK STARTUP OF THE RAMPAGE™ BOARD Although the Rampage board offers the most comprehensive set of marker controls available, your Rampage™ board requires NO programming and comes pre-configured with the most optimal default settings. Once installed, just Select a mode and GO PLAY! TOURNAMENT LOCK (BT USERS ONLY) Since the BT grip does not need a tool to change modes, there is a tournament lock switch located on the board. To use the Tournament lock feature, simply select the firing mode and the settings you want, open the grip, slide the tournament switch to the “on” position. When the tournament lock is switched to the “on” position, you will be prevented from switching modes via the rear mode switch.

SELECTING YOUR FIRING MODE Your Rampage™ board comes preloaded with 7 firing modes. To change modes, press the Mode Selector Button. Each time the Mode Selector Button is pressed, the LED indicator will blink, indicating what mode is selected. Each mode has a corresponding LED blink sequence. MODE Semi Burst

LED INDICATOR 1x Slow Yellow

MODE DESCRIPTION Fires 1 shot per each trigger pull.

x rounds fired per trigger pull (x = 2 to 5).

3x Fast Green

Reactive Full Auto

1 round fired per trigger pull and 1 round fired per trigger release.

2x Fast Red 6x Flicker Green

Fires continuously while the trigger is held.

Semi-Automatic until a x trigger-per-second pull rate, then transitions to programmable burst firing. Maintains burst firing until rate drops below x per second (x = 4 to 10)

Rampage 2x Fast Green

Semi-Automatic until a x trigger-per-second pull rate, then transitions to Reactive Mode. Maintains Reactive Mode until the trigger pull rate drops below x per second (x = 4 to10).

1x Slow Red

Prevents the marker from firing when the trigger is pressed.

1x Fast R/G/Y

Three shots in Semi-Automatic then Full Automatic on the 4th pull & hold. Resets to Semi-Automatic after 1 sec. of inactivity.

6x Flicker Yellow

Three shots in Semi-Automatic then transitions to 3 Round Burst. Resets to Semi-Automatic after 1 sec. of inactivity.

3x Fast Red

TOURNAMENT LOCK SWITCH NXL

INSTALLATION Before disassembling your grip, be sure you have a clean, clear workspace. need helps, PLEASE STOP and contact [email protected]

If you have questions about installation or

Before Installing your Rampage board, be sure to first remove the tape from the solenoid. Also remove Air source from you marker before attempting installation

A5/PRO-E USERS You must adjust the leaf on the micro switch to work properly with your trigger. To do so, use a pair of needle nose pliers and GENTLY bend the leaf slightly upward at the middle of the leaf. See example. Bend Here

After installation, you can tell if your switch is correctly adjusted if you can hear the micro switch “click” when you pull the trigger. If you do not hear the “click” try re-adjusting the bend in the leaf. You can also use your stock board as a guide as to how much bend is required. Do this BEFORE plugging in the battery

PROGRAMMING YOUR RAMPAGE™ BOARD

RAMPAGE™ BOARD SETPOINTS

Although most users will find the default operation sufficient, your Rampage™ board has unmatched flexibility when it comes to customization. Your Rampage™ board has 9 adjustable setpoints. To Enter/Exit Programming mode, Press and Hold the Mode button for 2 full seconds. The LED will Flash Red/Green 10 times.

SETPOINT

LED INDICATOR

DEFAULT

Debounce

Yellow

When you have reached the setpoint you wish to verify or adjust, press the Mode button again.

Burst Rounds

Fast Red

The LED will now repeatedly “blink” corresponding to the current setpoint value, allowing verification.

Rampage Rounds

Fast Green

Turbo+ Pull Rate

Fast Yellow

The LED will “flash” indicating it’s ready for a new setpoint value. Pull the trigger accordingly to enter the new setpoint value (the LED will blink for each trigger pull).

Rampage Pull Rate

Red Flicker

Press the Mode button one more time.

Base Group Enable

Green Flicker

Ramp Group Enable

Yellow Flicker

PROGRAMMING MODE The first programmable setpoint is the MGRF (the LED will be solid Red). Each trigger pull advances to the next setpoint indicated by the corresponding LED ID color (refer to the Setpoint Table).

Pulling the trigger again will advance to the next setpoint. To change the setpoint value, press the Mode button once again.

The LED will give you another “flash” indicating it has accepted the new setpoint value. The LED will revert back to “blinking” the new setpoint value. Verify your new value, then pull the trigger again to advance to the next setpoint.

MGRF - MAX GLOBAL RATE OF FIRE

Auto No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes No