RAMPAGE GEN 4 PROGRAMMING AND SETUP MANUAL FEATURING APE’S EXCLUSIVE DUAL CODE SOFTWARE! WARNING - ALL PERSONS WITHIN RANGE OF A PAINTBALL MARKER MUST USE PROPER EYE PROTECTION. NEVER DISASSEMBLE A MARKER WHILE IT IS UNDER PRESSURE WITH COMPRESSED AIR OR CO2. ALWAYS REMOVE THE AIR SOURCE BEFORE WORKING ON YOUR MARKER. ALWAYS FOLLOW THE MANUFACTURER’S INSTRUCTIONS WHEN USING OR WORKING ON YOUR MARKER. NOT FOLLOWING PROPER INSTRUCTION MAY CAUSE PERSONAL INJURY AND/OR POSSIBLE DAMAGE TO YOUR MARKER. USE THIS PRODUCT AT YOUR OWN RISK.
QUICK STARTUP OF THE RAMPAGE™ BOARD - Although the Rampage board offers the most comprehensive set of marker controls available, your Rampage™ board requires NO programming and comes pre-configured. Once installed, just add a 9 volt battery, select a mode and GO PLAY!
MORE OPTIONS - For Users that want to get the most out of their marker, go to www.GoApeOnline.com and download the Advanced Programming Guide. This guide will show you how to Unlock the advanced feature sets that are included in your board!
TOURNAMENT LOCK - Your Rampage Board has a tournament lock switch located on the board. Before installing your board, locate the switch (usually on the “small component” side of the board) and remove the protective orange tape cover. To use the Tournament lock feature, open the grip cover and slide the tournament switch to the “on” position (the “dot” side of the switch). The marker will be “locked” into the “Tournament Mode” setpoint and the “BPS Eyes On” rate of fire. While switched to the “on” position, you will be prevented from selecting firing modes and from accessing the programming mode.
POWER ON/OFF - Press the Power button to activate the marker. While the button is pressed, the battery level is displayed by the LED (Green = above 8.5V, Yellow = above 7.5V, Red = below 7.5V). If a ball is present in the breech, the marker starts in the current Firing Mode. If the breech is empty, the Empty Breech alert is displayed (Solid Purple). Press & Hold the power button for 1 sec. to start the marker with Eyes Off, or load the breech with paint. To turn the marker OFF, press/hold the power button for 3 seconds.
EYE CONTROL AND STATUS - (1 Button Markers) During firing operations, press/hold the Power Button for 1 second to toggle the Eyes On or Off. (2 button markers) During firing operations, tap the Eye Button to toggle the Eyes On or Off. The Eye status is as follows: (Solid Purple* = Empty Breech / Slow Purple* Flash = Eyes Off / Fast Purple* Flash = iFault Detected). Note that if the marker is in the Eyes Off state, you cannot switch firing modes. Re-enable the Eyes first, then select a new firing mode.
SELECTING A FIRING MODE - Your Rampage™ board comes preloaded with 8 firing modes. To change modes just tap the Power Button. Each mode has a corresponding LED color (refer to the Firing Mode Description Table). Your marker will always restart in the last active firing mode you shutdown with. PROGRAMMING MODE - To enter Programming Mode, press and hold the trigger while powering on the marker. Release the trigger and power
MARKER CONTROL SETPOINTS Feature
Default
Min/Max Value
BPS EYES ON BPS EYES OFF BPS FINE TUNE BPS CAPPED FIRING TRIGGER LEADING EDGE DEBOUNCE (MS) TRIGGER TRAILIING EDGE DEBOUNCE (MS) TRIGGER FILTER CONTROL
SOLID RED SLOW FLASH RED FAST FLASH RED FLICKERING RED SOLID GREEN SLOW FLASH GREEN FAST FLASH GREEN
TRIGGER FILTER TIMER (MS) AUDIO ENABLE EYE MODE EYE PROCESS BREECH LOAD DELAY (MS) ABS DWELL (MS) ABS RESET TIME (SEC) SOLENOID DWELL (MS) BOLT RETURN DELAY (MS) RAMP SEMI SHOTS RAMP PULL RATE RAMP MODE RAMP VALUE RAMP RESET (SEC) BURST ROUNDS REACTIVE ROUNDS BREAKOUT MODE TOURNEY MODE FIRING MODE GROUP 1 ENABLE/DISABLE FIRING MODE GROUP 2 ENABLE/DISABLE AUTO SHUT OFF TIMER (MIN) TUNE ASSIST START
FLICKERING GREEN SOLID YELLOW SLOW FLASH YELLOW FAST FLASH YELLOW FLICKERING YELLOW SOLID BLUE SLOW FLASH BLUE FAST FLASH BLUE FLICKERING BLUE SOLID PURPLE SLOW FLASH PURPLE FAST FLASH PURPLE FLICKERING PURPLE SOLID TEAL SLOW FLASH TEAL FAST FLASH TEAL FLICKERING TEAL SOILD W HITE SLOW FLASH W HITE FAST FLASH W HITE FLICKERING W HITE FLICKERING RED/GRN
FIRING MODE DESCRIPTION
Fires 1 shot per each trigger pull.
x rounds fired per trigger pull (x = 2 to 10).
Reactive
Yellow
x round fired per trigger pull and x round fired per trigger release. (x = 1 to 10)
Full Auto
Fires continuously while the trigger is held.
Red Flash
Semi-Automatic until a 5 trigger-per-second pull rate, then transitions to reactive firing. Maintains reactive firing until rate drops below 5 BPS (RAMP Mode is user adjustable)
the current setpoints for Dwell and Bolt Return Delay will both be overwritten by this procedure. To start, your marker MUST BE UNLOADED. Tune Assist is a “dry firing” process. Next, connect your marker to your air source.
Green Flash
Three shots in Semi-Automatic then transitions to 3 Round Burst. Resets to Semi-Automatic after 1 sec. of inactivity.
NOTE: Be sure you are starting with a FULL tank of air and have pre-adjusted your marker’s regulator to fire paint at approximately 285 fps before you begin. You may need to make fine adjustments to your regulator settings after completing the Tune Assist process. Also, when firing the marker in Tune Assist Mode, pause at least 1 second between trigger pulls.
Yellow Flash
Three shots in Semi-Automatic then Full Automatic on the 4th pull & hold. Resets to Semi-Automatic after 1 sec. of inactivity.
Blue Flash
Semi-Automatic until a 6 trigger-per-second pull rate, then transitions to 100% ramping. Maintains Ramping Mode until the trigger pull rate drops below 6 per second.
button. You’ll now be sitting at the first setpoint in the Marker Control Setpoint Table (BPS—Eye On / Solid Red LED). Use the trigger to advance/scroll forward thru the setpoint table and notice that each setpoint has a unique LED identification (ID). To change any setpoint, advance/scroll to the setpoint ID you wish to change, then tap the Power button. The LED will now…
The first 1022 words, extracted from the PDF. Read the full manual above, or download it.