RAMPAGE OLED PROGRAMMING AND SETUP MANUAL WARNING - ALL PERSONS WITHIN RANGE OF A PAINTBALL MARKER MUST USE PROPER EYE PROTECTION. NEVER DISASSEMBLE A MARKER WHILE IT IS UNDER PRESSURE WITH COMPRESSED AIR OR CO2. ALWAYS REMOVE THE AIR SOURCE BEFORE WORKING ON YOUR MARKER. ALWAYS FOLLOW THE MANUFACTURER’S INSTRUCTIONS WHEN USING OR WORKING ON YOUR MARKER. NOT FOLLOWING PROPER INSTRUCTION MAY CAUSE PERSONAL INJURY AND/OR POSSIBLE DAMAGE TO YOUR MARKER. USE THIS PRODUCT AT YOUR OWN RISK. Starting up your Marker - Press and hold the Power Button until the marker turns on, then release the power button to continue. Shutting down your Marker - To power down your maker, press and hold the Power Button until your marker shuts off. Firing Mode Control - While the marker is displaying the Run Screen, tap the Power Button to scroll thru all enabled firing modes. Eye Control -Your marker will display the “Eyes On” icon on your OLED display when enabled and fire at the Eyes On rate of fire. When the eye function is disabled, the “Eyes Off” icon will appear on the OLED display and your marker will fire at the Eyes Off rate of fire. (2 button markers) Tap the Eye Button to toggle the eye function On or Off. (1 button markers) Press & Hold the power button for 1 second to toggle the eye function On or Off. Programming Mode - To enter programming mode, start up the marker while holding down the trigger. Release the power button and trigger to continue. Note: your maker will not start in Programming mode if the tourney lock switch is on. To exit Programming mode either power down the marker or scroll until the “x” appears in the upper right corner of the screen. When the “x” is displayed, pull and hold the trigger to return to live firing mode. Menu Navigation and Adjustments - Pull and release the trigger to scroll through the available menu options. An arrow on the left side of the display will indicate your current selection. To select a menu option, simply pull and hold the trigger. Once you scroll past the last option in a menu, the “Back Arrow” icon appears in the upper left corner of the OLED display. When selected, the back arrow option returns to the previous menu in the tree. (2 button markers) Tap the Power Button to increase a value / Tap the Eye Button to decrease a value. (1 button markers) Tap or Press/Hold the Power to increase a value / Values rollover to their minimum. Start Menu Profile Load Menu: This option lets you load a profile. You can define up to six individual profiles. A profile stores a complete collection of setpoints and allows you to completely reconfigure your marker instantly. Hot Start Menu: This option lets you quickly access the following options: − Uncapped Firing: Instantly uncap the rate of fire on your marker − Breakout Mode: Instantly turns on the currently defined Breakout mode − Dry Fire Mode: Instantly bypasses eye processing for dry firing at the Eyes On rate of fire Program Menu: This menu provides access to all the marker setpoints. Each time you program your marker, you store the programmed setpoints in a profile. You can program up to six individual profiles. From this menu you can also access the Global Setpoints (those that apply to all marker operations), the Tuning Assist function and the Reset Menu. More info on these options is provided later in this document. Trigger Trainer Mode (TTM): This option puts you into “training” mode that lets you measure how fast you can pull the trigger. This mode will capture your Average and Peak pull rates, and display a bar graph based on your current pull rate. To start a training cycle, pull the trigger repeatedly for a short burst. When you stop pulling, the marker will update the OLED display with your pull rate data. Pull another trigger burst to measure your rate again. Statistics: This option displays the following statistical information about your marker: • Peak Pull Rate: This displays the highest Pull Rate achieved since the last reset • Total Pulls: This displays the total number of trigger pulls since the last reset • Total Shots: This displays the total number of Bolt cycles/Shots fired since the last reset. This total is also used for your “memo” function. All of these statistical counters can be reset to zero from the “Reset Menu”. Marker Setpoints • Trigger Leading Edge Debounce: The Leading Edge debounce timer compensates for the inherent contact bounce/bobble whenever the trigger switch is pulled. This setpoint is the minimum amount of time the trigger switch contacts must be closed to validate a trigger pull. It can also filter out the effects of mechanical recoil that occur during marker operation. Mechanical recoil disturbances can physically “retrip” the trigger switch, and by increasing the timer value, a recoil disturbance can potentially be filtered out. This timer can be used in conjunction with the Trigger Filter Controls when the mechanical adjustability of the trigger is inadequate or unable to compensate for recoil disturbances. • Trigger Trailing Edge Debounce: The Trailing Edge debounce timer compensates for the inherent contact noise generated whenever the trigger switch is released. This setpoint is the minimum amount of time the trigger switch contacts must be open to validate a trigger release. Noise on the trigger release can potentially cause the marker to “queue” another trigger pull when in fact a valid trigger pull was not made by the shooter. Recoil disturbances can also generate contact bounce/bobble on the trigger release. Longer trailing edge times can also be a pseudo trigger “hold-off” timer, not allowing any new trigger pulls after trigger release until the trailing edge timer has expired. • Trigger Filter Control : When activated, this timer prevents ANY trigger activity from being registered as a valid trigger pull and subsequently queued up for the ensuing shot. This filter should be used when the mechanical adjustability of the trigger is inadequate or unable to…
The first 1016 words, extracted from the PDF. Read the full manual above, or download it.