THE SAFETY SYSTEM
The NINJA FLEX Regulator is equipped with an ASTM COMPLIANT bottle Burst Disk required by the Department of Transportation (D.O.T) In addition to the required safety burst disk, the regulator has a Low Pressure (LP) safety burst disk. The LP safety burst disk is there to protect you and your marker in the unlikely event your Ninja FLEX regulator fails. REMEMBER, Most regulator failures are the result of contaminated air. If the LP safety burst disk vents, it did so for a reason. We recommend you do the following: •
NINJA ROTATIONAL FLEX REGULATOR OWNERS MANUAL Patent No.: US 11,169,550 B2
ADJUSTABLE OUTPUT REGULATORS 300-900psi 1.877.NINJAUSA (1.877.646.5287)
Disassemble the regulator ( refer to Service and Rebuild procedures), inspect the regulator for contamination and clean if necessary. • Install a new LP Burst disk, PER THE INSTRUCTIONS ON PAGE 6, Available at most paintball the system. shops and If the LP burst disk vents after rebuild see and airsmith for help or call : 1.877.NINJAUSA (1.877.646.5287) NINJA REGULATORS have a Safety Vent Groove on the stem (as shown in below image). This lifesaving feature allows for the venting of the bottle, in the event the regulator is unscrewed from the bottle with pressure present in the bottle. ALWAYS CHECK TO MAKE SURE THERE IS NO GAP BETWEEN THE BOTTLE AND REGULATOR SEAL. SEE ILLUSTRATION BELOW. IF THERE IS A GAP STOP!! DO NOT FILL OR USE YOUR SYSTEM
VIDEO GUIDES Dual Seal O-Rings
DUE TO THE HIGH FLOW CHARACTERISTICS OF THE PIN REGULATOR YOU MAY EXPERIENCE CONNECTION / ACTIVATION DIFFICULTIES WITH CERTAIN MARKERS. TO ELIMINATE SIMPLY ADJUST REGULATOR OUTPUT PRESSURE TO 500PSI OR BELOW. SEE PAGE 4 FOR PRESSURE ADJUSTMENT. SEE OUR YOUTUBE CHANNEL FOR FULL GUIDES
WARNING: This is not a toy. Misuse may cause seri-
paintball must be worn by the user and persons within range. Recommend 18 years or older to purchase. Persons under 18 must have adult supervision. READ OWNERS MANUAL BEFORE USING © 2010-2023 Pressure Specialist Inc.
FILLING THE NINJA FLEX REGULATOR SYSTEM
The FLEX Regulator system is equipped with the industry standard “QD Style” either on or the marker. The which allows your FLEX Regulator system to be with clean dry Compressed Air or Nitrogen. FLEX Regulator system may be
UNDER NO CIRCUMSTANCES SHOULD THE FLEX REGULATOR SYSTEM BE FILLED WITH PURE OXYGEN. OXYGEN WILL IGNITE CAUSING INJURY OR DEATH. When
your FLEX Regulator system do not exceed the pressure rating shown on the CYLINDER’S LABEL. DO NOT APPLY OR INJECT OIL OF ANY TYPE INTO THE FILL OR BURST DISK PORTS. OIL WILL VAPORIZE AND POSSIBLY IGNITE DURING THE FILL PROCEDURE CAUSING INJURY OR DEATH
It is important to keep dirt, oil, and water out of your FLEX Regulator system. Most nipple regulator failures are due to dirt or contamination. Always keep a cover on the when you are not the Flex Regulator system. If you use compressed air, make sure and moisture that the compressor providing that air is equipped with WORKING separators.
CONNECTING YOUR FLEX REGULATOR
PRIOR TO EVERY USE OF YOUR NINJA FLEX AIR SYSTEM PLEASE DO THE FOLLOWING. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SERIOUS INJURY. • INSPECT TO MAKE SURE THE BONNET SET SCREWS (X3) AND ROATATIONAL RING SET SCREWS (X3) ARE PRESENT AND SECURELY TIGHTENED. • DO NOT USE THE NINJA FLEX AIR SYSTEM IF ANY OF THE BONNET OR ROTATIONAL RING SET SCREWS ARE MISSING OR NOT SECURELY TIGHTENED. NEVER REMOVE THE SET SCREWS OR ADJUST THE ROTATIONAL RING WITH PRESSURE IN THE BOTTLE. ROTATIONAL ADJUSTMENT: DO NOT ADJUST WITH AIR IN YOUR TANK: TANK MUST BE EMPTY. The following tools are required and are available at most hardware stores: • 5/64 Allen Wrench (included) • Soft jaw pliers to assist in bonnet removal you may wish to After connecting your Ninja FLEX regulator system into your markers ASA orientate your Ninja FLEX regulator. The Ninja Flex regulator has a full 360 degree rotation. Follow these simple steps:
BEFORE PROCEEDING, MAKE SURE YOUR SYSTEM HAS BEEN COMPLETELY DEGASSED BY DEPRESSING THE OUTPUT PIN UNTIL NO TRAPPED GAS IS PRESENT.
ASTM .825-14 NGO Thread
Rotational Ring Pressure Adjustment Collar
Output Gauge Bottle Gauge
No Gap Here Low Profile OFV Fill Valve
High & Low Pressure Burst Disks (Not Pictured) ASTM Safety Vent Groove
© 2010-2023 Pressure Specialist Inc.
PRESSURE ADJUSTMENT
Unless ordered otherwise, all Ninja FLEX Regulators are shipped at their lowest pressure output page of this manual. setting. VIDEO GUIDES AVAILABLE using QR code provided on
ALWAYS WEAR EYE PROTECTION, GLOVES AND POINT THE AIR SYSTEM IN A SAFE DIRECTION AWAY FROM YOURSELF AND ALL BYSTANDERS PRIOR TO DEGASSING OR ADJUSTING THE SYSTEM! NOTE: THE FOLLOWING TOOL MAY BE REQUIRED AND WAS SHIPPED WITH YOUR FLEX REGULATOR: 30-32 Hook spanner wrench. When adjusting you must activate or vent the regulator with every 1/6 of a turn or every notch on the adjusting collar.
DO NOT EXCEED AN OUTPUT PRESSURE OF MORE THAN 1200PSI You should you always start at the lowest setting and adjust up to the desired output. Please note the adjustment marks on the adjustment collar indicating which way will increase or decrease the output pressure. Turning the collar up toward the bonnet will lower/decrease the output pressure and turning the collar down toward the body will raise/increase the output pressure. NOTE: TO REDUCE WEAR ON THE ADJUSTMENT COLLAR WE RECOMMEND YOU PERIODICALLY APPLY A DROP OR TWO OF AIR TOOL OIL TO THE ADJUSTMENT COLLAR THREADS ON THE GAS DISTRIBUTION BODY (#17) AND TO EACH ADJUSTMENT BALL (#14)
THE OUTPUT GAUGE (MARKED “OUTPUT” ON THE GAS DISTRIBUTION BODY) WILL NOT SHOW ANY ADJUSTMENT TO PRESSURE WHEN DECREASING UNTIL THE SYSTEM IS VENTED OR ACTIVATED.
TOURNAMENT LOCK SLEEVE To prevent any pressure adjustment while Included with your Ninja FLEX regulator is a Tournament Lock Sleeve. Simply slide over regulator prior to installation on your marker to ensure compliance with any rules and regulations. This sleeve is constructed out of non…
The first 1000 words, extracted from the PDF. Read the full manual above, or download it.