Watch the video at: www.ninjapaintball.com
NEW NINJA BALL REGULATOR SYSTEM OWNER'S MANUAL 30% INCREASED FLOW!
MADE IN USA ASTM compliant, NINJA Regulators can toggle from STANDARD 750-850 PSI to a medium 600700 PSI or low 450-550 PSI output in a few minutes, eliminating the need to purchase 2 regulators or separate spring kits, see page 4.
WARNING:
This is not a toy. Misuse may cause serious injury or death. Eye protection designed specifically for paintball must be worn by the user and persons within range. Recommend 18 years or older to purchase. Persons under 18 must have adult supervision. READ OWNER’S MANUAL BEFORE USING.
THE SAFETY SYSTEM
The NINJA Regulator is equipped with an ASTM COMPLIANT bottle Burst Disk required by the Department Of Transportation. (D.O.T.) In addition to the required safety burst disk, the regulator has a Low Pressure (LP) safety burst disk (stamped 1.8K).
FILLING THE NINJA REGULATOR SYSTEM
UNDER NO CIRCUMSTANCES SHOULD THE NINJA REGULATOR SYSTEM BE FILLED WITH PURE OXYGEN. OXYGEN WILL IGNITE CAUSING INJURY OR DEATH
When filling your NINJA Regulator system do not exceed the pressure rating shown on NINJA REGULATOR CYLINDER’S LABEL.
DO NOT APPLY OR INJECT OIL OF ANY TYPE TO THE FILL OR BURST DISC PORTS. OIL WILL VAPORIZE AND POSSIBLY IGNITE DURING THE FILL PROCEDURE CAUSING INJURY OR DEATH
It is important to keep dirt, oil and water out of your NINJA Regulator system. Most regulator failures are due to dirt or contamination. Always keep a cover on the fill nipple when you are not filling the NINJA Regulator system. If you use compressed air, make sure that the compressor providing that air is equipped with WORKING filters and moisture separators.
CONNECTING YOUR NINJA REGULATOR
SLOWLY Screw your NINJA Regulator system into your markers ASA fitting. It is recommended that you apply Ninja Lube on the NINJA Regulator bonnet threads. This simple procedure will reduce bonnet and ASA thread wear. The NINJA Regulator has a “Ball Valve” output valve which shuts off the gas delivery when the power system is removed from the marker.
Due to the high flow characteristics and 30% increased flow of the NEW NINJA Ball Seal Regulator you may experience connection / activation difficulties with certain markers ASA. To eliminate simply reduce regulator output pressure by removing (1 or 2) shims, see page (4), Pressure Conversion.
BALL VALVE SEAT REPLACEMENT 1. The Ball Valve Seat #4 sits inside of the bonnet #2 in the bonnet pocket. To replace the Ball Valve Seat #4 use a small pick to gently pull the Ball Valve Seal from the bonnet taking care to not damage the seat. 2. When replacing the Ball Valve Seat #4 into the bonnet #2 place the seal within the inner bonnet pocket and gently push it into place using the eraser end of a pencil or similar small blunt ended object.
ALWAYS CHECK TO MAKE SURE THERE IS NO GAP BETWEEN THE BOTTLE AND REGULATOR SEAL. SEE ILLUSTRATION BELOW. IF THERE IS A GAP.
The 1.8K PSI safety burst disk is there to protect you and your marker in the unlikely event that the NINJA Regulator fails.
STOP!!! DO NOT FILL OR USE YOUR SYSTEM. Place the system on the ground and wait for the system to FULLY DEGAS! Contact a qualified airsmith IMMEDIATELY! OR CALL 1.877.NINJAUSA (1.877.646.5287) for assistance
REMEMBER, most regulator failures are the result of contaminated air.
If the (LP) 1.8K PSI safety burst disk vents, it did so for a reason. We recommend you do the following: Disassemble the regulator (refer to Service and Rebuild procedures), inspect the regulator for contamination and clean if necessary. Install a new 1.8K PSI burst disc, PER THE INSTRUCTIONS SEE PAGE 6, available at NINJAPAINTBALL.COM and refill the system.
No Gap Here
If the (LP) 1.8K PSI burst disc vents after rebuild see an airsmith for help or call: 1.877.NINJAUSA (1.877.646.5287)
The NINJA Regulator system is equipped with the industry standard “QD Style” fill fitting, which allows your NINJA Regulator system to be refilled either on or off the marker. The NINJA Regulator system may be filled with either Clean, Dry Compressed Air or nitrogen.
NINJA REGULATORS have a Safety Vent Groove on the stem (As shown in above image). This lifesaving feature allows for the venting of the bottle, in the event that the regulator is unscrewed from the bottle with pressure present in the bottle.
PRESSURE CONVERSION
Unless ordered otherwise, all NINJA Regulators are factory shipped at a standard 750-850 PSI output pressure, If you wish to adjust the output pressure please follow these six steps. WATCH THE VIDEO AT WWW.NINJAPAINTBALL.COM
BEFORE PROCEEDING, MAKE SURE YOUR SYSTEM HAS BEEN COMPLETELY DEGASSED VIA THE OUTPUT BALL VALVE, TO INSURE THAT NO TRAPPED COMPRESSED GAS IS PRESENT!
ALWAYS WEAR EYE PROTECTION, GLOVES AND POINT THE AIR SYSTEM IN A SAFE DIRECTION AWAY FROM YOURSELF AND ALL BYSTANDERS PRIOR TO DEGASSING THE SYSTEM!
NOTE: THE FOLLOWING TOOLS ARE REQUIRED AVAILABLE AT MOST HARDWARE STORES: • •
3/32" HEX KEY WRENCH TO REMOVE BONNET SET SCREWS 10-32 THREADED SCREW 2" TO 4" LONG TO REMOVE BONNET
1. Remove the two 10-32 set screws that lock the Bonnet (the top portion of the regulator) to the Reg Body, REFER TO DIAGRAM ON PAGE 8. 2. Unscrew the Bonnet counter clockwise from the Reg Body. (It has normal right hand threads.) Bonnet should remove easily. Make sure there is no trapped air in the bonnet by depressing the pin valve. Helpful Hint: Insert the 10-32 x 2" to 4" screw into one of the bonnet set screw holes to ease the removal and reinstallation of the bonnet. Insert the screw into one of the bonnet screw holes until it stops or bottoms out, unscrew (1/4 to 1/2) turn. This will prevent the screw from damaging the gas body bonnet threads. Use the inserted screw to remove the bonnet.
Be careful not to lose the brass Output Ball Valve or its spring. 3. PRESSURE ADJUSTMENT: The shims are located in the bottom “pocket” of the gas distribution body. Due to the NINJA Regulator being hand crafted and tested THE NUMBER OF SILVER…
The first 1023 words, extracted from the PDF. Read the full manual above, or download it.