NINJA X REGULATOR OWNERS MANUAL CUSTOM OUTPUT PRESSURE 1.877.NINJAUSA (1.877.646.5287)
VIDEO GUIDES
NINJA X REGULATORS FEATURE A RECESSED BALL DESIGN. THIS IS NOT COMPATIBLE WITH TRADITIONAL PAINTBALL STYLE AIR SOURCE ADAPTERS. YOU MUST USE A “LONG PIN” ASA TO ACTIVATE THE BALL. IN CERTAIN CIRCUMSTANCES THE BALL MAY BE REMOVED ENTIRELY. IN THESE CASES THE REGULATOR MAY ONLY BE FILLED ONCE FULLY CONNECTED TO THE GUN OR ADAPTER.
WARNING: This is not a toy. Misuse may cause seri-
paintball must be worn by the user and persons within range. Recommend 18 years or older to purchase. Persons under 18 must have adult supervision. READ OWNERS MANUAL BEFORE USING © 2010-2023 Pressure Specialist Inc.
THE SAFETY SYSTEM
The NINJA Regulator is equipped with an ASTM COMPLIANT bottle Burst Disk required by the Department of Transportation (D.O.T) In addition to the required safety burst disk, the regulator has a Low Pressure (LP) safety burst disk The LP safety burst disk is there to protect you and your airgun in the unlikely event your Ninja regulator fails. REMEMBER, Most regulator failures are the result of contaminated air. If the LP safety burst disk vents, it did so for a reason. We recommend you do the following: Disassemble the regulator ( refer to Service and Rebuild procedures), inspect the regulator for contamination and clean if necessary. Install a new LP Burst disk, PER THE INSTRUCTIONS ON PAGE 6, Available at most paintball or If the LP burst disk vents after rebuild see and airsmith for help or call : 1.877.NINJAUSA (1.877.646.5287) NINJA REGULATORS have a Safety Vent Groove on the stem ( as shown in below image). This lifesaving feature allows for the venting of the bottle, in the event the regulator is unscrewed from the bottle with pressure present in the bottle. ALWAYS CHECK TO MAKE SURE THERE IS NO GAP BETWEEN THE BOTTLE AND REGULATOR SEAL. SEE ILLUSTRATION BELOW. IF THERE IS A GAP STOP!! DO NOT FILL OR USE YOUR SYSTEM smith IMMEDIATELY OR CALL 1.877.NINJAUSA
ASTM .815-14 NGO THREAD REMOVABLE BONNET LOW PRESSURE BURST DISK
LOW PROFILE FILL VALVE (Not Pictured)
Recessed Ball Bonnet
HIGH PRESSURE BURST DISK
HIGH PRESSURE GAUGE
ASTM SAFETY VENT GROOVE © 2010-2023 Pressure Specialist Inc.
NO GAP HERE
FILLING THE NINJA X REGULATOR SYSTEM The X Regulator system is equipped with the industry standard “QD X X Regulator system may be dry Compressed Air or Nitrogen. UNDER NO CIRCUMSTANCES SHOULD THE FLEX REGULATOR SYSTEM BE FILLED WITH PURE OXYGEN. OXYGEN WILL IGNITE CAUSING INJURY OR DEATH. X Regulator system do not exceed the pressure rating shown on the CYLINDER’S LABEL. DO NOT APPLY OR INJECT OIL OF ANY TYPE INTO THE FILL OR BURST DISK PORTS. OIL WILL VAPORIZE AND POSSIBLY IGNITE DURING THE FILL PROCEDURE CAUSING INJURY OR DEATH It is important to keep dirt, oil, and water out of your X Regulator system. Most regulator compressor providing that air is equipped with WORKING tors.
CONNECTING YOUR X REGULATOR SLOWLY Screw your X recommended that you apply lube on the X Regulator bonnet threads. This simple procedure will reduce bonnet and ASA thread wear. The X gas delivery when the system is removed from the Ninja PCP Fill Station or gun ASA Fitting.
DUE TO THE HIGH OUTPUT OF THE X REGULATOR IT HAS BEEN DESIGNED WITH A RECESSED BALL STYLE ACTIVATION. THIS CANNOT BE USED IN ANY TRADITIONAL SHORT PIN ASA’S OR ADAPTERS. A LONG PIN MUST BE USED
© 2010-2023 Pressure Specialist Inc.
Extracted from the PDF. Read the full manual above, or download it.