THE SAFETY SYSTEM
January 2023
The NINJA PRO V2 Regulator is equipped with an ASTM COMPLIANT bottle Burst Disk #12 required by the Department of Transportation (D.O.T) In addition to the required safety burst disk #12, the regulator has a Low Pressure (LP) safety burst disk #16 (stamped 1.8K) The LP (1.8K) safety burst disk #16 is there to protect you and your marker in the unlikely event your Ninja PRO V2 regulator fails.
WARNING: Remember, most regulator failures are the result
of contaminated air.
If the LP (1.8K) safety burst disk #16 vents, it did so for a reason. We recommend you do the following: Disassemble the regulator (refer to Service and Rebuild procedures), inspect the regulator for contamination and clean if necessary. Install a new LP (1.8K) Burst disk, PER THE INSTRUCTIONS ON PAGE 6, Available at most paintball shops and refill the system.
NINJA OFV PIN PRO V2-V4 REGULATOR OWNER’S MANUAL STANDARD - SLP - SHP For more information visit www.NinjaPaintball.com or please call us at (815) 477-0007
If the LP (1.8K) burst disk #16 vents after rebuild see and air smith for help or call us at: 1(815) 477-0007. NINJA PRO V2 REGULATORS have a Safety Vent Groove on the stem (As shown in below image). This lifesaving feature allows for the venting of the bottle, in the event the regulator is unscrewed from the bottle with pressure present in the bottle.
WARNING: ALWAYS CHECK TO MAKE SURE THERE IS NO
GAP BETWEEN THE BOTTLE AND REGULATOR SEAL. SEE ILLUSTRATION BELOW.
WARNING: IF THERE IS A GAP STOP!! DO NOT FILL OR USE
YOUR SYSTEM.
Visit our YouTube Channel for informational product videos https://www.youtube.com/user/ninja186 DUE TO THE HIGH FLOW CHARACTERISTICS OF THE NINJA PRO V2 PIN REGULATOR, YOU MAY EXPERIENCE CONNECTION / ACTIVATION DIFFICULTIES WITH CERTAIN MARKERS ASA. TO ELIMINATE SIMPLY REDUCE THE REGULATOR OUTPUT PRESSURE TO 450PSI BY REMOVING (3) BLUE SHIMS (#12) SEE PAGE 8, PRESSURE CONVERSION. WE ALSO HAVE VIDEOS SHOWING ADJUSTMENT ON OUR YOUTUBE CANNEL NAME IS NINJA PAINTBALL OFFICIAL.
WARNING: This is not a toy. Misuse may cause serious injury
or death. Eye protection designed specifically for paintball must be worn by the user and persons within range. Recommend 18 years or older to purchase. Persons under 18 must have adult supervision. READ OWNERS MANUAL BEFORE USING.
Safely drain your system and wait for the system to fully degas. Contact a qualified Air smith immediately or call us at: 1(815) 477-0007.
© 2010-2023 Pressure Specialist Inc.
FILLING THE NINJA PRO V2 - V4 REGULATOR SYSTEM
PRESSURE ADJUSTMENT - SLP is not adjustable Unless ordered otherwise, all standard Ninja PRO V2 Regulators are factory shipped at a Standard 750-800 PSI output pressure (SHP at 1100 PSI), If you wish to adjust the output pressure, please follow these six steps. Video guides available using the QR code provided or the URL address on the front page of this manual.
The NINJA PRO V2 Regulator system is equipped with the industry standard “QD Style” fill fitting #13, which allows your Ninja PRO V2 Regulator system to be refilled either on or off the marker. The Ninja PRO V2 Regulator system may be filled with clean, dry Compressed Air or Nitrogen.
WARNING: Under no circumstances should the regulator
system be filled with pure oxygen. Oxygen will ignite causing injury or death. When filling your regulator system do not exceed the pressure rating shown on the cylinder’s label.
WARNING: Do not apply or inject oil of any type into the fill or burst disk ports. Oil will vaporize and possibly ignite during the fill procedure causing injury or death.
It is important to keep dirt, oil, and water out of your Ninja PRO V2 Regulator system. Most regulator failures are due to dirt or contamination. Always keep a cover on the fill nipple when you are not filling the Ninja PRO V2 Regulator system. If you use compressed air, make sure that the compressor providing that air is equipped with working filters and moisture separators.
CONNECTING YOUR NINJA PRO V2 - V4 REGULATOR
WARNING: Prior to every use if your Ninja PRO V2 air system
please do the following.
1. Failure to follow these instructions can result in serious injury. 2. Inspect to make sure the bonnet screws #2 (3) and rotational sleeve #11 set screws X (3) are present and securely tightened. 3. Do not use the Ninja PRO Air system if any of the bonnet or rotational sleeve set screws #2 & #11 are missing or not securely tightened. 4. Never remove the set screws #2 & #11 or adjust the rotational sleeve #14 with pressure in the bottle.
Rotational Adjustment
Do not adjust with air in your tank: Tank must be empty.
NOTE: The following tools may be required and are available at most hardware stores: - 5-64 Allen Wrench After connecting the Ninja PRO V2 Regulator system into your markers ASA fitting may wish to orient your NINJA PRO V2 Regulator. The NINJA PRO V2 Regulator has full 360-degree rotation. Follow these simple steps:
WARNING: Before proceeding, make sure your system has been completely degassed via the output pin valve #6, to ensure that no trapped compressed gas in present. WARNING: Do not adjust with air in your tank. Tank must be
1. Using a 5-64 allen wrench loosen (turn counterclockwise) the (3) Rotational collar set screws #11. DO NOT REMOVE THE SCREW. 2. Grasp the bottle and turn the NINJA PRO V2 Regulator to your desired location. 3. Tighten the (3) 8-32 rotational collar set screws #11 securely. Fill your air system and you are ready to play. © 2010-2023 Pressure Specialist Inc.
WARNING: Always wear eye protection, gloves and point the
air system in a safe direction away from yourself and all bystanders prior to degasing or adjusting the system! NOTE: The following tools may be required and are available at most hardware stores: - 5/64” Hex key wrench to remove bonnet set screws #2. - 8-32” Threaded machine screws 2” to 4” long to help remove bonnet.
WARNING: Before proceeding make sure your system has
The first 1016 words, extracted from the PDF. Read the full manual above, or download it.