NINJA PRO V3 STD REGULATOR OWNER’S MANUAL STANDARD - FACTORY PRESET AT 550 PSI (+/- 50 PSI) For more information and PRO V3 product videos visit: www.NinjaPaintball.com Visit our YouTube Channel for informational product videos https://www.youtube.com/user/ninja186 WARNING: This is not a toy. Misuse may cause serious injury or death. Eye protection designed specifically for paintball must be worn by the user and persons within range. Recommend 18 years or older to purchase. Persons under 18 must have adult supervision. READ OWNERS MANUAL BEFORE USING. REFER TO THE NINJA PRO V3 REGULATOR PART DIAGRAM FILLING THE NINJA PRO V3 REGULATOR SYSTEM The NINJA PRO V3 Regulator system is equipped with the industry standard “QD Style” fill fitting #12, which allows your Ninja PRO V3 Regulator system to be refilled either on or off the marker. The Ninja PRO V3 Regulator system may be filled with clean, dry Compressed Air or Nitrogen. © 2023 Pressure Specialist Inc.
WARNING: Under no circumstances should the regulator system be filled with pure oxygen. Oxygen will ignite causing injury or death. When filling your regulator system do not exceed the pressure rating shown on the cylinder’s label. WARNING: Do not apply or inject oil of any type into the fill or burst disk ports. Oil will vaporize and possibly ignite during the fill procedure causing injury or death. It is important to keep dirt, oil, and water out of your Ninja PRO V3 Regulator system. Most regulator failures are due to dirt or contamination. Always keep a cover on the fill nipple when you are not filling the Ninja PRO V3 Regulator system. If you use compressed air, make sure that the compressor providing that air is equipped with working filters and moisture separators. CONNECTING YOUR NINJA ACE REGULATOR WARNING: Prior to every use if your Ninja PRO V3 air system please do the following. 1. Failure to follow these instructions can result in serious injury. 2. Inspect to make sure the bonnet screws #2 (3) and rotational sleeve #19 set screws, LOCATED BELOW THE PRO V3 LOGO, X (3) are present and securely tightened. 3. Do not use the Ninja PRO V3 Air system if any of the bonnet or rotational sleeve set screws #2 are missing or not securely tightened. 4. Never remove the set screws #2 or adjust the rotational sleeve #19 with pressure in the bottle. ROTATIONAL ADJUSTMENT Do not adjust with air in your tank: Tank must be empty. NOTE: The PRO V3 was shipped with a 5/64 Allen wrench key. After connecting the Ninja PRO V3 Regulator system into your markers ASA fitting you may wish to orientate your NINJA PRO V3 Regulator. The Ninja PRO V3 Regulator has full 360-degree rotation. © 2023 Pressure Specialist Inc.
FOLLOW THESE SIMPLE STEPS: WARNING: Before proceeding, make sure your system has been completely degassed via the output pin valve #6, to ensure that no trapped compressed gas in present. WARNING: Do not adjust with air in your tank. Tank must be empty. 1. Using the 5/64 allen wrench loosen (turn counterclockwise) the (3) TOP Rotational collar set screws #2. DO NOT REMOVE THE SET SCREWS. 2. Grasp the bottle and turn the NINJA PRO V3 Regulator to your desired location. 3. Tighten the (3) TOP rotational collar set screws #2 securely. 4. Fill your air system. THE SAFETY SYSTEM The NINJA PRO V3 Regulator is equipped with an ASTM COMPLIANT bottle Burst Disk #11 required by the Department of Transportation (D.O.T). In addition to the required safety burst disk #11, the regulator has a Low Pressure (LP) safety burst disk #14 (stamped 1.8K). The LP (1.8K) safety burst disk #14 is there to protect you and your marker in the unlikely event your Ninja PRO V3 regulator fails. WARNING: Before proceeding, make sure your system has been completely degassed via the output pin valve #6, to ensure that no trapped compressed gas in present. WARNING: Remember, most regulator failures are the result of contaminated air. If the LP (1.8K) safety burst disk #14 vents, it did so for a reason. We recommend you do the following: Disassemble the regulator (refer to Service and Rebuild procedures), inspect the regulator for contamination and clean if necessary. Install a new NINJA LP (1.8K) Burst disk #14, PER THE INSTRUCTIONS ON PAGE 9-10. © 2023 Pressure Specialist Inc.
Extracted from the PDF. Read the full manual above, or download it.