PAINTBALL LOADER OWNERS MANUAL
valken.com
QUICK SET UP GUIDE
1. Install the batteries following the “Battery Installation” instructions on page 2. 2. Mount the V-Max+ loader onto your marker. Make sure the loader feedneck is pushed down as far as possible into your markers feedneck for the most secure fit. Be careful not to over tighten your markers feedneck as it may damage the feedneck of your V-Max+ loader. 3. Turn on your V-Max + loader push and hold the On/Off button located on the rear of the loader under the LED light. You will hear the loader spin if there are no paintballs in the feedneck and the LED light will blink Blue-full battery green-medium battery or red-low battery 4. Fill your V-Max+ loader with paintballs . This feeds the paintballs into the feedneck and breach of your marker and your V-Max+ loader will stop spinning
1. Remove the single screw on the underside of the battery door. NOTE: This screw is optional and not needed to retain the battery door.
2. Slide the battery door toward the rear of the loader.
3. Open the battery door and load two 9-Volt batteries according to the diagram on the outside of the battery door. Close the battery door and replace optional screw if desired.
2. Push the hinge pin barrel to the left to disengage the right side of the lid hinge.
3. Pull the right side of the hinge upward and rotate the left side of the hinge out of the socket in the top shell.
REMOVING THE LID
5. Turn off your V-Max+ Loader by pressing & holding the On/Off button until you see the red light and then release the on-off button. Also your V-Max+ Loader will automatically shut off in one of two ways QUICK SET UP GUIDE • Feeds 30+ BPS
• Quick Change Lid
• 220 Ball Capacity
• Fast Battery Change
• Ultra Lightweight
• One Touch On/Off
• Fast Disassembly
• Uses two 9 Volts
A 60 minute power down if eyes are blocked (motor not running) B 10 minute power down if eyes are unblocked (motor running)
1. Open the lid.
TROUBLESHOOTING • V-Max+ Loader will not turn on when pressing the On/Off button. Check the batteries for correct polarity alignment. Check the battery strength & replace with fresh, name-brand batteries if necessary. Contact Valken if further problems persist.
DISASSEMBLY
• Breaking paintballs in my V-Max+ Loader. Make sure to use fresh, quality paintballs in your V-Max+ Loader.
1. Press down on the rear latch on the interior of the loader toward the front ofthe loader. NOTE: The latch is under constant tension.
2. Lift the top shell while the rear latch is pressed forward until the top shell is free.
3. Push the top shell forward to disengage the front latch and remove the top shell completely.
• V-Max+ Loader is slow or not performing as usual. Make sure the loader is clean and replace the batteries with fresh, name-brand batteries. CLEANING AND MAINTENANCE • The V-Max+ Loader should be disassembled and cleaned if: A paintball is broken in the loader or paint/shell fragments enter the loader. When dirt or debris enters the loader. For routine cleaning every few days of play. • The V-Max+ Loader should be disassembled and cleaned using a non-abrasive cloth. If there is still paint residue, use a damp cloth to remove the remaining paint. Warning: Do not get the board or electrical components wet. Be sure the loader is completely dry before reassembling. • The V-Max+ Loader requires fresh, quality name-brand batteries to achieve optimum performance.The batteries will need to be regularly replaced to get the highest performance from your V-Max+ Loader.
4. Remove the center plate by gripping the inside edge and top of the plate. Pull the tab out from under the rear latch, then the front latch, to free the plate.
5. Remove the Drive Assembly by rotating the cup latch 90 degrees and disconnecting the wiring harness.
6. Clean any paint from the loader and interior with a non abrasive cloth. Warning: Do not get the board or electrical components wet.
Extracted from the PDF. Read the full manual above, or download it.