INSTRUCTIONS FOR USE The EVO grip frame is capable of high rates of fire and an agitating hopper such as a VL Revolution, Halo, or Evolution 2 is recommended for better performance. EVO BATTERY: The EVO comes with a 9 volt rechargeable battery. You must charge it for a full 22 hours before initial use since the it does not come fully
charged. For best long term battery life, repeat this process every time it is drained. You can also use a regular 9 volt battery with this frame if your rechargeable battery is dead or if you want to play with the frame right away. You will need to remove the right grip panel when you need to replace it.
WARNING: PMI RECOMMENDS USING THE 9V RECHARGEABLE BATTERY PROVIDED FOR OPTIMAL PERFORMANCE. DO NOT USE THE BATTERY CHARGER WHEN USING ANY NON-RECHARGEABLE BATTERY. SAFETY: Read your instruction manual and follow all the rules of marker safety. When you turn the marker on by holding the on/off button for three seconds, it automatically goes into "safe mode." To turn the safety off, press the on/off button once lightly. The red on/off Flush Cocking Rod indicator will turn on and the marker is now ready to fire. Electronic Anti-Chop Eye
PMI High Performance Rifled Barrel
Locking Velocity Thumb Adjuster
On/Off Button
To turn the marker back on safety, press the on/off button once and the red on/off indicator will turn off. To turn the marker off hold the on/off button for three seconds while it is in safe mode. The frame should be left off when not using the marker or you will drain the battery. Low Pressure Gauge ON/OFF BUTTON: The on/off is the silver button located on the left hand side of the gripframe. Push it once and hold it in for three full seconds to turn your Evo LCD on. The LCD will turn on, but the marker is in "safe mode." Press the on/off button again and the safety will Adjustable turn off. The red on/off indicator will then light up. TIMER: The Evo must be in "safe mode" to change the timer set-
Sear Release LCD (see below) On/Off Indicator Charge Port
DSR Regulator
tings. Press button B on the right hand side once to change settings. Once Adjustable Drop Forward 10º Bottom Line the numbers are blinking use button A to increase timer clock by one minute Adapter increments. Press button B once when the countdown time is set and the numbers will stop blinking. To start the timer, turn the safety SEAR RELEASE SLIDE: The sear release slide is located on the left hand off and fire the marker once. side of the EVO grip frame. To reinstall the bolt/block/hammer assembly, push the sear release slide up before the hammer comes in contact with the sear. ODOMETER: The Evo must be in "safe mode" to view the odometer. That will allow the bolt/block/hammer assembly to slide easily into the marker. Press the A button to view the odometer. LCD DISPLAY
REG PRESSURE: The regulator pressure can be changed with a 1/8” allen
wrench. Screwing the adjustment screw in will lower the pressure. The regulator should be set near 300 psi to get 300 fps. Lower regulator pressure will lower velocity, but if the pressure gets too low, the marker might not recock.
00 00 Counter/Timer
Eye Indicator
WARNING: Never use water to clean the marker, or you run the risk of damaging the electronic trigger frame.
ELECTRONIC ANTI-CHOP EYE (ACE): When the ACE is activated, it will only allow you to fire when there is a paintball in the chamber. When the
ACE is off, the rate of fire defaults to a slower setting so you won't chop paint. However, this means you will not be able to dry fire the marker quickly. To turn the ACE on or off, press button B on the right hand side of the frame while the marker is ready to fire. The Eye logo on the LCD will only appear while the ACE is turned on.
1. Vertical Feed Receiver–Gold Fade 2. Barrel–Gold 3. Ram Air Chamber–Gold 3B. Ram Air Spring 3C. Ram Air Piston 3D. Piston O-Ring 5. Field Strip Pin Assembly 6. Valve Body 7. Valve Cup Seal Assembly 8. Vertical Top Tube–Gold 9. Valve Guide 10. Valve Spring 11. Grey Venturi Bolt 12. Rear Block w/ Cushion 13. Flush Cocking Rod 14. Hammer Assembly 15. Hammer Spring 16. ASA O-Ring 17. Spring Guide 18. Vertical ASA–Gold 19. Left Eye Cover 20. Ball Detents 21. LCD Gripframe Assembly 22. Sear Release Slide 23. LCD Grips 24. Right Eye Cover 25. Thumb Adjust Velocity Screw 25A. Velocity Lock Screw 26. Valve Set Screw
ASA Screw Ball Detent/Eye Cover Screws Rear Trigger Frame Screw Grip Screws Front Trigger Frame Screw Bolt Pin Velocity Screw O-Ring Rear Block O-Rings Blue Hammer O-Ring Screen Filter Bolt O-Rings Valve O-Rings Ram Air Chamber O-Ring Regulator O-Ring Trigger Assembly Barrel O-Ring 3.75” Hose Bottom Line SS Screws 10˚ Bottom Line Adapter–Charcoal Sear 90° Elbow Flush Cocking Guide O-Ring C-Clip Retaining Washer Flush Spring Drop Forward–Charcoal Sear Spring Trigger/Sear Pin Sear Spring Pin
Disassembly of electronic trigger frame will void warranty.
Trigger Spring Low Pressure Gauge NGO Top Reg Seat Seal Poppet O-Ring (013-70) Poppet Reg Seat Base O-Ring (006-70U) DSR Reg Spring Reg Seat Base Reg Body Mid (black) Bottom Swivel (black) Bottom Bolt O-Ring (012-70) Bottom Bolt Adjusting Screw Adjusting Screw O-Ring DSR 10-32 Plug Seal Stop O-Ring (002-70) Interior Bottom Bolt O-Ring (010-70) Clear EVO Eye Smoke EVO Eye Board Screws Board Cover Upper EVO Board LCD Board LCD Board Screws 8.4 Volt Battery Charge Port Cover
Extracted from the PDF. Read the full manual above, or download it.