07GTIInstructions
INSTRUCTIONS FOR USE The Piranha® GTI is capable of high rates of fire and an agitating hopper such as an Extreme Rage® Overdrive™ is recommended for better performance. WARNING: READ OPERATOR’S MANUAL BEFORE USE. EVERY PERSON WITHIN RANGE OF AN AREA WHERE A PAINTBALL MARKER IS IN USE MUST WEAR PROTECTIVE GOGGLES AND HEADGEAR SPECIFICALLY DESIGNED FOR PAINTBALL. WARNING: ALWAYS COCK MARKER BEFORE ATTACHING AIR SOURCE. MARKER CAN DISCHARGE IF AIR SOURCE IS ATTACHED BEFORE MARKER IS COCKED. THE MARKER CONTAINS COMPRESSED GAS OR AIR WHEN PRESSURIZED. NEVER DISASSEMBLE MARKER UNTIL REMOVING ALL GAS OR AIR FROM THE SYSTEM. RULES FOR SAFE HANDLING OF COMPRESSED GAS OR AIR MUST BE FOLLOWED AT ALL TIMES. WARNING: WHEN COCKING THE PRESSURIZED MARKER, DO NOT RELEASE THE COCKING KNOB UNTIL AFTER THE COCKING MECHANISM HAS LOCKED BACK INTO THE COCKED POSTITION; RELEASING THE COCKING KNOB DURING COCKING CAN CAUSE THE MARKER TO SHOOT. PMI High Performance Barrel
Cocking Rod
Dual Ball Detents Safety Slide
OPERATING THE PIRANHA® GTI: 1. Attach threaded barrel
firmly to marker. 2. At this time, do not attach air source or loader and do not load paintballs into marker. 3. Insert barrel plug firmly into barrel. 4. Pull the cocking knob straight back from the rear of the marker until the cocking mechanism locks back in the cocked position. Always cock marker before airing it up. During cocking the flush cocking rod will recoil or “spring back” into the marker once released and will only move slightly during marker operation. 5. Slide safety “off,” 6. Squeeze the trigger with an even pressure. You should hear the hammer and bolt assembly slide forward. 7. Cock the marker. 8. Before attaching the air source, read and understand the section in the manual on “Compressed Gas/Air.” Follow safety rules for handling compressed gas/air. If any leak occurs in the marker, refer to troubleshooting guide or to a qualified airsmith. Use only cylinders for compressed gas or air that comply with all applicable laws and regulations, including but not limited to those of the U.S. Department of Transportation, OSHA, Compressed Gas Association, and/or American Society for Testing and Materials. 9. With goggles on, test for function after attaching air source: Squeeze the trigger. The marker should shoot air and the cocking knob should cycle slightly after each trigger squeeze, repeat several times. Flush cocking rods will bobble some, but they will not come out all the way. 10. Slide safety forward (semi version). Paintballs may then be loaded.
Velocity Adjustment Screw
Sear Release
Gas Thru Grip
Bottom Line Adapter
WARNING: BEFORE DISASSEMBLY, STORAGE, OR TRANSPORT OF THE MARKER, REMOVE AIR SOURCE FIRST, THEN REMOVE ALL PAINTBALLS FROM THE MARKER, BARREL, AND LOADER. REMOVE ALL GAS OR AIR FROM THE MARKER. INSERT BARREL PLUG AND SLIDE THE MECHANICAL SAFETY FORWARD SO THE SAFETY IS ENGAGED AND THE RED DOT IS NOT LIT. THE SAFETY IS A SMALL MECHANICAL SLIDE ON THE LEFT SIDE OF THE MARKER ABOVE THE TRIGGER. WHEN THE SAFETY IS “OFF,” A RED DOT IS VISIBLE ON THE MARKER. THE TRIGGER CAN STILL BE PULLED IF THE SAFETY IS “ON,” BUT THE MARKER WILL NOT FIRE OR DE-COCK. E-FORCE MODEL: THE ON/OFF BUTTON ON THE LEFT SIDE OF THE FRAME SHOULD BE USED AS SAFETY.
1A. Milled Receiver Body - Matte Black 1B. Milled Receiver Body - Matte Blue 1C. Milled Receiver Body - Matte Gunmetal 2. 9” Barrel 3. End Cap GTI 5. Field Strip Pin Assembly 6. Valve Body 7. Red Valve Cup Seal Assembly 7. Black Valve Cup Seal Assembly 8A. Removable Low Rise - Matte Black 8B. Removable Low Rise - Matte Blue 8C. Removable Low Rise - Matte Gunmetal 9. Valve Guide 10. Valve Spring 11. Molded Flush Cocking Bolt 12. Molded Flush Cocking Rear BlockAssembly 13. Molded Flush Cocking Rod 14. Hammer Assembly 15. Blue Hammer Spring 16. ASA O-ring 17. Spring Guide 18A. Vertical ASA Adapter - Matte Black 18B. Vertical ASA Adapter - Matte Blue 18C. Vertical ASA Adapter - Matte Gunmetal 19L. Ball Detent Cap Left 19R. Ball Detent Cap Right 20. Ball Detent 21. Polymer Frame Assembly ‘07 22. Sear Release Slide 23. Wrap Around Grip 25. Velocity Screw 26. Valve Set Screw
27. ASA Screw 28. Ball Detent Screw 29. Rear Trigger Frame Screw 29A. Front Trigger Frame Screw 30. Grip Screws 32. Bolt Pin 33. Velocity Screw O-Ring 34. Valve/Rear Block O-Rings 35. Blue Hammer O-Ring 36. Screen Filter 37. Bolt O-Rings 37. Gas Thru Grip O-Ring 37. ASA Slug O-Ring 38A. Trigger 38B. Trigger Pawl Assembly 39. Barrel O-Ring 40. Gas-Thru Foregrip 41. 6.25" SS hose 42. Bottom line SS screw 43. Straight Bottomline Adapter 44. Sear 45. 90° Elbows 46. Safety Slide 47. Safety Ball 48. Safety Spring 53. Flush Spring 55. Trigger Spring 56. Sear/Trigger Pin 57. Trigger/Spring Pin 58. Sear Spring 59. Front Bolt O-Ring 67. 1/8th” NPT Plug
Extracted from the PDF. Read the full manual above, or download it.