RAVAGE INSTRUCTIONS FOR USE The Ravage eForce grip frame is capable of high rates of fire and an agitating hopper such as an Extreme Rage Overdrive, VL Revolution, Halo, or Evolution 2 is recommended for better performance. RAVAGE BATTERY: The Ravage comes with a 9 volt rechargeable battery. You must charge it for a full 22 hours before initial use since the it does not come fully charged.
For best long term battery life, repeat this process every time it is drained. You can also use a regular 9 volt battery with this frame if your rechargeable battery is dead or if you want to play with the frame right away. You will need to remove the right grip panel when you need to replace it.
WARNING: PMI RECOMMENDS USING THE 9V RECHARGEABLE BATTERY PROVIDED FOR OPTIMAL PERFORMANCE. DO NOT USE THE BATTERY CHARGER WHEN USING ANY NON-RECHARGEABLE BATTERY. Cocking Rod On/Off Button
PMI High Performance Barrel
ON/OFF BUTTON: The on/off is the silver button
located on the left hand side of the gripframe. Push it once Gas Thru Grip and the red on/off indicator will then light up. Push the on/off button again to turn it off. The frame should be left off when not using the marker or you will drain the battery.
Velocity Adjustment Screw On/Off Indicator
Sear Release
Charge Port BURST BUTTON Press the Burst Button once to turn the marker on 3
Shot Burst. Press the Burst Button again to turn the frame to 6 Shot Burst. Press the Burst Button again to turn the frame to 9 Shot Burst. Press the Burst Button again to turn it back to semi-auto. FULL AUTO BUTTON Press the Full Button once to turn the frame to
Full Auto. Press the Full Button again to turn it back to semi-auto. eFORCE BATTERY The eForce frame comes with a 9 volt
rechargeable battery. You must charge it for a full 22 hours with the marker turned off before initial use since it does not come fully charged. For best long term battery life, repeat this process every time it is drained. You can also use a regular 9 volt battery with this frame if your rechargeable battery is dead or if you want to play with the frame right away. You will need to remove the right grip panel when you need to replace it. A blinking on/off indicator light means your eForce frame needs to be charged right away. Always charge with the marker turned off.
10º Bottom Line Adapter
Drop Forward
SEAR RELEASE SLIDE: The sear release slide is located on the left
hand side of the Ravage grip frame. To reinstall the bolt/block/hammer assembly, push the sear release slide up before the hammer comes in contact with the sear. That will allow the bolt/block/hammer assembly to slide easily into the marker. TOURNAMENT LOCK SWITCH The Tournament Lock Switch
enables you to play in a tournament or at a field that does not allow full auto and burst modes by restricting the marker to semi-automatic only. All eForce frames come with the Tournament Lock off so you can immediately put the marker in full auto or burst mode. See Piranha manual (5.3) page 32 or Piranha manual (5.1) page 28.
WARNING: Never use water to clean the marker, or you run the risk of damaging the electronic trigger frame.
E! LUSIV
1. Milled Receiver Body 2. 9” Barrel 3. ASA Slug 4. Sight Rail 5. Field Strip Pin Assembly 6. Valve Body 7. Valve Cup Seal Assembly 9. Valve Guide 10. Valve Spring 11. Minlon Bolt 12. Rear Block w/ Cushion 13. Minlon Cocking Rod 14. Hammer Assembly 15. Blue Hammer Spring 16. ASA O-ring 17. Spring Guide 18. Vertical ASA Adapter 19. Ball Detent Cap 20. Ball Detent 25. Velocity Screw 26. Valve Set Screw 27. ASA Screw 28. Ball Detent Screw 31. Sight Rail Screws 32. Bolt Pin 33. Velocity Screw O-Ring 34. Rear Block O-Rings 35. Blue Hammer O-Ring 36. Screen Filter 37. Valve O-Rings 37. Gas Thru Grip O-Ring 37. ASA Slug O-Ring
39. Barrel O-Ring 10161 10788 40. Gas-Thru Foregrip 41. 7" SS hose 47015 42. Bottom line SS screw 42016 42013 43. 10˚ Bottom Line Adapter 45. 90° Elbows 47000 54. Drop Forward 71242 57738 59. Front Bolt O-Ring 60. Standard Cocking B/B/H Assembly 71297 61. eForce Polymer Double Trigger Frame Assembly59093 71585 62. eForce Sear Release Slide 70105 63. Grip 71583 64. Rear Trigger Frame Screw 65. Front eForce Trigger Frame Screw 71582 66. Grip Screws 10782 67. eForce Trigger 71586 68. eForce Sear 71591 71587 69. eForce Trigger Spring 71588 70. eForce Sear/Trigger Pin 71. eForce Trigger/Spring Pin 71589 72. eForce Sear Spring 71590 73. eForce Board Screws 71592 71593 74. eForce Board Cover 71594 75. eForce Electronic Board 71595 76. eForce Solenoid 77. eForce Charge Port Cover 71596 78. 8.4V Rechargeable Battery 70181
Extracted from the PDF. Read the full manual above, or download it.