INSTRUCTIONS FOR USE
The Pro-E grip frame is capable of high rates of fire and an agitating hopper such as a VL Revolution, Halo, or Evolution 2 is recommended for better performance. COCK MARKER BEFORE AIRING UP: Due to low pressure valving, you
must cock the marker first or it may leak down the barrel. Simply pull the cocking rod in the back of the marker and the flush cocking rod will slide back into the marker after it is cocked.
Cocking Rod
Velocity Adjustment ON/OFF BUTTON: The on/off is the blue button located on
the left hand side of the grip frame. Push it once to turn your Pro-E on. Push it again and the frame will turn off. The frame should be left off when not using the marker or you will drain the battery.
Sear Release Red Button
SAFETY: Read your instruction manual and follow all the rules of marker
safety. Hold the green button down to turn the marker to Semi, Burst or Full Auto. Lightly pressing the Green Button will cycle through the menus.
Blue Button On/Off
Charge Port
MODES OF FIRE: All menus can be accessed in Safe Mode
Burst – 1-5 shot burst (red button) Count A – 0 to 160 (red button) ROF – 1-15 (red button) (controls burst and full modes) ROF MAX – 1-15 (controls semi mode only) Timer – 60:00 (red button to change) (blue button starts countdown) LCD DISPLAY Alarm
Tournament Lock Battery Indicator
COUNT A B
00:00 Counter/Timer
Fire Modes
SAFE SEMI bur FULL
BURST TIMER ROF MAX Safe Mode Only Menus
LCD (see below)
Regulator Adjustment
Green Button Change Modes/ Scroll Menu
SEAR RELEASE SLIDE: The sear release slide is located on the left hand
side of the Pro-E grip frame. To reinstall the bolt/block/hammer assembly, push the sear release slide up before the hammer comes in contact with the sear. That will allow the bolt/block/hammer assembly to slide easily into the marker. REG PRESSURE: The regulator pressure can be changed with a 1/8” allen
wrench. Screwing the adjustment screw in will lower the pressure. The regulator should be set near 300 psi to get 300 fps. Lower regulator pressure will lower velocity, but if the pressure gets too low, the marker might not recock.
WARNING: Never use water to clean the marker, or you run the risk of damaging the electronic trigger frame.
PRO-E BATTERY: The Pro-E comes with a 9 volt rechargeable battery. You must charge it for a full 22 hours before initial use since the it does not come
fully charged. For best long term battery life, repeat this process every time it is drained. You can also use a regular 9 volt battery with this frame if your rechargeable battery is dead or if you want to play with the frame right away. You will need to remove the right grip panel when you need to replace it.
WARNING: PMI RECOMMENDS USING THE 9V RECHARGEABLE BATTERY PROVIDED FOR OPTIMAL PERFORMANCE. DO NOT USE THE BATTERY CHARGER WHEN USING ANY NON-RECHARGEABLE BATTERY. TOURNAMENT LOCK SWITCH: The tournament lock switch enables you to play in a tournament or at a field that does not allow full auto and burst
modes by restricting the marker to semi-automatic only. Pro-E frames come with the tournament lock off so you can immediately put the marker in full auto or burst mode. The lock is a silver button you can access by removing the right grip panel and lifting out the battery. Simply press it once to turn the lock on.
1. Vertical Feed Receiver 2. Barrel 3. Ram Air Chamber 3B. Ram Air Spring 3C. Ram Air Piston 3D. Piston O-Ring 4. Sight Rail 5. Field Strip Pin 6. EXT Valve Body 7. Valve Cup Seal Assembly 8. Vertical Top Tube 9. Valve Guide 10. Valve Spring 11. Venturi Bolt 12. Flush Cocking Rear Block w/ Cushion 13. Flush Cocking Rod 14. Hammer 15. Hammer Spring 16. ASA O-Rings 17. Spring Guide 18. Vertical ASA 19. Ball Detent Cap 20. Ball Detent 21. Double Trigger Frame Assembly 22. Sear Release Slide 23. Pro-E Grips 25. Thumb Adjust Velocity Screw 25A. Velocity Lock Screw 26. Valve Set Screw 27. ASA Screw 28. Ball Detent Screw 29. Trigger Frame Screws 30. Grip Screws 32. Bolt Pin 33. Velocity Screw O-Ring 34. Rear Block O-Rings 35. Hammer O-Ring
37. Bolt O-Ring 37. Valve O-Ring Front 37. ASA O-Ring Front 37. Ram Air body O-Ring 37. Regulator O-Ring 38. Pro-E Trigger 39. Barrel O-Ring 41. 4.4” Hose 42. Bottom Line SS Screws 43. 10˚ Bottom Line Adapter 44. Sear 45. 90° Elbow 50. Flush Cocking Guide O-Ring 51. C-Clip 52. Retaining Washer 53. Flush Spring 54. Drop Forward 55. Trigger Spring 56. Trigger/Sear Pin 57. Sear Spring Pin 67. Low Pressure Gauge 68. Reg NGO Top 69. Reg Seat Seal 70. Reg Poppet O-Ring (013-70) 71. Reg Poppet 72. Reg Seat Base O-Ring (006-70U) 73. Reg Spring 74. Reg Seat Base 75. Reg Body Mid (black) 76. Reg Bottom Swivel (black) 77. Reg Bottom Bolt O-Ring (012-70 Buna) 78. Reg Bottom Bolt 79. Reg Adjusting Screw 80. Reg Adjusting Screw O-Ring 81. Reg DSR 10-32 Plug 82. Reg Seal Stop O-Ring (002-70) 83. Interior Bottom Bolt O-Ring (010-70)
Disassembly of electronic trigger frame will void warranty.
Extracted from the PDF. Read the full manual above, or download it.