HATER PAIN TBALL “HATRED NXT/SFT Shocker Board” HATRED Software Version 4 Featur es:
Designed from the ground up for both the Shocker SFT and Shocker NXT. The first ever paintball circuit board with a fully integrated wireless transceiver! Fully compatible with all SYMBIO wireless products. Includes 22 firing modes including fully customizable ramp modes. Compatible with both reflective and break-beam Shockers. Proprietary multi-tasking algorithms continuously monitor all trigger and eye events to ensure that all pulled shots register and are processed. TEN TIMES faster than the top-ranked competitor! This translates to 900,000 more operations per second than anyone else. Gold plated leads ensure rock solid intra-circuit communication. Fully adjustable ABS features add to the marker’s dwell to eliminate that pesky first shot drop-off. Anti-mechanical bounce (AMB) algorithms solve the problem of physical switch bounce. No need to worry when the refs pull that old slow trigger pull trick on your gun. A “forced shot” feature allows the user to clear the marker of eye faults. Instant on feature. After all, you wanna play now! Instantaneous battery status. Tournament lock feature allows the user to “lock out” the programming mode in order to meet specific field/tournament guidelines.
Instal l ati on:
MAKE SURE THE MARKER IS NOT CONNECTED TO AN AIR SOURCE AND DOES NOT HAVE PAINTBALLS IN THE BREACH DURING INSTALLATION!!!!!! 1. 2. 3. 4. 5. 6.
Remove the screws that secure the grips. This will expose the board. Carefully remove the two pins behind the trigger. These pins go through the microswitch and mount the circuit board to the frame. Unplug the battery and wiring harness from your old board. Plug the wiring harness into your new HATRED board. Carefully place the new HATRED board into your frame and reinsert the mounting pins through the microswitch. Attach a fresh 9v battery and insert the battery into the frame. Make sure the leads from the battery are tucked away from the circuit board and towards the rear of the frame. Be very careful not to scratch the back of your circuit board with the battery. Circuit boards which are
damaged due to incorrect installation are not covered under warranty. Replace grips. VERY IMPORTANT. Enter the programming menu and set your eye type (break-beam or reflective) before you use the marker. Please see the “programming” and “eye sensor operation” headers on how to do this. Power on and play!
LED’ s: The HATRED gun board has two LED’s. The button LED is a single color, blue LED that is seen through the Shocker’s rear button. The onboard LED is a multi-color LED that is physically mounted on the bottom of the HATRED Shocker board. We suggest using translucent grips so you can see the onboard LED as it makes the programming and operation of your marker much easier.
Power On: The HATRED board comes equipped with an Instant On feature. Simply press the power button and your marker will instantly power on. As long as the power button is depressed, you will see a flickering GREEN or RED led on the Onboard LED. The GREEN indicates a good battery and the RED means replace the battery as soon as possible. Regardless of GREEN/RED battery indication, your marker WILL REGISTER YOUR FIRST TRIGGER PULL! Please be careful! Power Off: To turn the marker off, press and hold the button for two seconds. As the gun powers down, the onboard LED will go through a rainbow power down sequence. Please note that this particular rainbow LED sequence does NOT indicate that you’re entering the programming menu.
Blue Fickering Teal
To enter the programming menu, hold the trigger down and THEN turn the marker on. The onboard LED will inform the user that the programming mode has been accessed by flashing several colors rapidly.
LED Col or
Setti ng
Defaul t Setti ng
Adj ustabl e R ange
Purple Green Red Blue Teal Yellow White
Fire Mode Debounce Dwell Max ROF AMB Eye Delay Wireless Address ABS
Flickering Purple Flickering Green Flickering Red Flickering
Ramp Activation Ramp Percent Reset
1➠Breakbeam 2➠Reflective
Pulling and releasing the trigger will allow the user to toggle through the different programming options. 2.) Once the desired setting/LED color is reached, pull and hold the trigger to select that setting. The onboard LED will then go blank. 3.) Once the onboard LED goes blank, pull the trigger for the desired setting. For example, if the user wishes to set the debounce to 2, he or she must pull the trigger two times. ➠If the user wants to view their current value for a particular setting, he or she need only to continue holding the trigger in after the setting is selected from the menu. The software will then blink back the user’s current value for that particular setting. 4.) The software will indicate that the new value has successfully been entered by blinking the value back to the user then rapidly flashing the LED through a spectrum of colors. ➠As the software blinks back the new setting, the user may abort this process by simply clicking the trigger once. The new settings will still be saved. 5.) After a setting has been changed, the user may change another option or power the gun off to save the settings. NOTE: All “programming clicks” correspond exactly to their settings. If you want to cap the ROF at 15, pull the trigger 15 times. If the user sets the value too low (2 cps ROF cap for example), the software will automatically default to the lowest accepted value. The inverse is also true for user inputs which are beyond the adjustable range.
Pr ogr ammi ng Ex ampl es:
Pr ogr ammi ng
The bottom dip switch must be in the OFF position in order to enter the programming menu. If the bottom dip switch is ON, “tournament lock” will be enabled and the user will be unable to program the marker.
Defaults Eye Type
To set the firing mode to PSP mode. 1. 2. 3. 4. 5. 6.
The first 1006 words, extracted from the PDF. Read the full manual above, or download it.