Dye e.Voke System - English

LED INDEX DURING CHARGING. 0 - 10%

Solid red

Blinks red once every 2 seconds

Blinks blue once every 2 seconds

Blinks green once every 2 seconds

Solid green

During use, the e.VOKE will alert you when your power level becomes low.

SYNC YOUR M2 WITH MOSAIR AND i5 E.VOKE SYSTEM

• Make sure your M2 is Air Sync compatible and the Air Sync module is installed. • Make sure the M2 Air Sync is turned on. Go to “PROFILE SETUP” to turn Air Sync on. • Return to play mode on M2. • Turn e.VOKE on. • M2 and e.VOKE will automatically sync. If the e.VOKE and M2 MOSAir do not automatically sync, please follow this process. • Turn both e.VOKE and M2 MOSAir on. • Hold the rear #3 button down on e.VOKE to initiate search for M2 device. • On M2 go to “PROFILE SETUP”, scroll to the Bluetooth screen select twice to enter setup menu. Initiate i5 pairing search by pressing joystick on your M2. • e.VOKE will verbally alert you when M2 is connected. The i5 logo on the M2 play screen will turn blue when connected to the i5.

LED INDEX CHART OPERATION/STATUS

LED COLOR LED STATUS

Power ON / OFF

Solid for 3 seconds

Bluetooth Unpaired

Rapid blink 4 times per sec.

Bluetooth Paired/ not connected yet

Blinks once per second

Bluetooth Paired/ connected

Blinks once every 3 sec.

Bluetooth connected status checking > if disconnected

Bluetooth connected status checking >if re-connected

INSTALLING e.VOKE IN YOUR M2 WITH MOSAir BOARD

• The Air Sync module is only compatible with the M2 MOSAir main Board. • MOSAir boards are identified by their Blue color and wireless charging system on the opposite side of the Prism OLED Screen.

FOR OLDER M2 MODELS BEING UPGRADED

• M2 markers produced in 2016 will need to be upgraded with the MOSAir main board to facilitate the e.VOKE system. • The MOSAir board comes standard with CFC wireless charging. The power receiver is connected and mounted to the main board, on the opposite side of the OLED screen. • The wireless CFC component will only fit under 2017 v2 sticky grips.

Photo A

• 2017 v2 Sticky grips are identified by the DYE M2 label located inside the grip on the back side of the M2 logo jewel (photo A). • If you have an older model M2 that does not have MOSAir and a v2 Sticky grip contact DYE or your local retailer to order. • The MOSAir and e.VOKE system can be used without the wireless charging unit installed, and can therefore be used with v1 2016 sticky grips

M2 MOSAir “AIR SYNC” INSTALLATION

• Make sure your M2 is Air Sync compatible (needs to be upgraded to MOSAir) and the Air Sync chip module is installed in the M2 MOSAir board. • Turn on your M2 by pushing and holding the center of the joystick until your M2 powers on. • M2 Air Sync needs to be turned on. To perform this operation, push the M2 joystick in the up position until you enter the “PROFILE SELECT SCREEN” • Select the profile you plan on using (examlpe P1, P2 etc..) Enter into the profile by pushing and holding the joysitck in for one second. This will put you into “PROFILE SETTINGS”. • Once you are in profile settings, using your joystick, toggle to the right two times, to reach the “BLUETOOTH ICON”. • Once on the bluetooth screen, push in the center of the joystick in until “OFF” is highlighted white. • Then pull the joystick down once to turn the bluetooth to the “ON” mode. • Then press the center of the joystick in to save this setting and then the word “SETUP” will appear.

Photo B

Photo D

Photo C

• Push the center of the joystick in again for one second to enable your M2 to prompt you to “SYNC” to the I5 e.VOKE unit. • Push and hold the center of the joystick in again for one second to “SELECT TO SYNC” • This will trigger your M2 to search for the e.VOKE device blutooth signal and attempt connection. • You will need to have the M2 and e.VOKE within one foot distance of eachother to connect. • Turn on your e.VOKE by pushing and holding the e.VOKE center #2 button, until it powers on. You will see a green power on light on the e.VOKE unit. • Then push and hold the e.VOKE rear #3 button and you will hear an auditory message “SEARCHING FOR DEVICE” from your e.VOKE unit. • Upon successful connection, you will hear an auditory message from your e.VOKE stating “PAIRED”. • Your M2 and e.VOKE are now successfully connected.

IF YOUR e.VOKE DOES NOT CONNECT, REPEAT THE SYNC PROCESS.

• While on the “CONNECTION FAILED” screen, press the center of the M2 joystick for 1 second “SELECT TO RETRY”, this will allow your M2 to search for your e.VOKE. • With your e.VOKE on, press and hold the rear #3 button to allow your e.VOKE device to search for your M2. • Upon successful connection, you will hear an auditory message from your e.VOKE stating “PAIRED”.

REMOVING THE i5 LENS TIP: It is recommended that you replace your lens at least once each year.

Factory applied protective coatings on each lens surface will wear off even with gentle cleaning and regular use abrasion. You should also always replace your lens after taking a direct paintball hit from within 10 feet.

1 Removing the i5 lens is a quick two step process. Step 1 depress the top locking tab on the gray frame retention clip and push this tab forward in the lens locking channel. Step 2 then depress the lower locking tab on the gray frame retention clip and push the gray frame retention clip forward. Perform this on both 1 sides of the mask. (See figure 1) You can also use the cyan locking hook finger grooves to assist you in sliding the unit forward when pushing the tabs to clear the release hook. (See figure 2) 2 Once both…