DYE Precision, Inc. USA 10637 Scripps Summit Ct. San Diego, CA 92131 P 858-536-5183 F 858-536-5191 GERMANY Albert Einstein Str. 2 B 77656 Offenburg, Germany P +49 (0)781 639 349 91 ASIA No. 253, Guojhong Rd., Dali Dist. Taichung City 412, Taiwan (R.O.C.) P +886 (0) 4-2407-9135 F +886 (0) 4-2407-2090 www.dyepaintball.com Copyright ©2015 DYE Precision, Inc. The stylized “dye” logo, the “sphere” logo and the DM logo are either registered trademarks, trademarks, or design trademarks of DYE Precision, Inc. Made in Taiwan
OWNER’S MANUAL
R-2 ™ LOADER OWNER’S MANUAL
QUICK GUIDE SET UP
FEATURES / SPECS. • Adjustable Ball Capacity: 200/260 Paintballs • Lid With Integrated Rapid Release Safeguard System
• Reload Alert System
• MISUSE OF PAINTBALL EQUIPMENT MAY CAUSE SERIOUS INJURY OR DEATH.
• Active Power Conservation • Low Power Indicator
• PLEASE READ, UNDERSTAND AND FOLLOW THE DIRECTIONS IN THE R-2 LOADER OWNER’S MANUAL.
• Dynamic Force Control • Adjustable Drive Spring Force
• EYE PROTECTION THAT IS DESIGNED SPECIFICALLY FOR PAINTBALL AND MEETS ASTM/CE STANDARDS MUST BE WORN BY USER AND PERSONS WITHIN RANGE.
• Improved Feed Reliability • Positive Feed Live Hinge Tray • Power Supply: Three AA Batteries • Feed Rate: 52 Balls Per Second • Weight: 1.3 Lbs (Empty, without batteries) • Dimensions: 4.75”H X 8.5”L X 4.25”W U.S. and International Patents Pending.
WARNING IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES.
• Tool-Less Disassembly
• RECOMMEND 18 YEARS OR OLDER TO PURCHASE. PERSON UNDER 18 MUST HAVE ADULT SUPERVISION. • IF YOU READ THESE INSTRUCTIONS AND DO NOT FULLY UNDERSTAND THEM OR ARE UNSURE OF YOUR ABILITY TO MAKE NECESSARY ADJUSTMENTS PROPERLY, CALL DYE OR YOUR LOCAL PRO SHOP FOR HELP.
BATTERY INSTALLATION No tools are required for battery installation, just follow the simple instructions found on page 3. Three AA batteries are required to operate the R-2 Loader. When installing the batteries make sure to install them the correct way by following the + and – polarity markings on the battery holder. MOUNTING R-2 LOADER ON A MARKER Make sure the R-2 Loader is securely mounted on your marker’s feedneck and the R-2 Loader’s feed tube is bottomed out on your marker’s feed neck. It is recommended to use an adjustable clamping feed neck system with the R-2 Loader. Do not over tighten your marker’s feed neck on the R-2 Loader as it may damage the loader.
Figure 1a
TURNING THE R-2 LOADER ON / OFF Once the batteries have been installed and the R-2 Loader is fully assembled, simply press the power button at the rear of the R-2 Loader (see figure 1a). As soon as the LED light indicator comes on, the loader is ready to go. There is no programming or boot up sequence to worry about, just load up paintballs and go. IF R-2 LOADER JAMS PAINT In the unlikely event that the R-2 Loader jams paint, simply give the jam release trigger a quick pull. This will turn the center rotor arm in reverse, quickly clearing the jam. The jam release trigger is located on the underside of the R-2 Loader (see figure 1b). NOTE: Results may very depending on the quality of paintballs used with the rotor loader.
Figure 1b 2
BATTERY INSTALLATION INSTALL / CHANGE BATTERIES 1. Remove the R-2 Loader from your marker. 2. Empty all paintballs from the R-2 Loader. 3. Remove Top Shell, and Tray/Window component (see page 5 for proper disassembly instructions). 4. Install batteries into battery holder. Pay attention to the + and – symbols. 5. Use Velcro strap to secure batteries in place and prevent batteries from coming dislodged during play. 6. Reassemble R-2 by following directions on page 7. The R-2 has a low battery indicator built in. The R-2’s LED will flash red if the batteries are low and need to be replaced.
WARNING
• LOW BATTERIES MAY CAUSE THE R-2 LOADER NOT TO FUNCTION PROPERLY. • DIRT AND HEAVY DUST CAN CREATE EXCESS FRICTION AND CAUSE THE LOADER TO MALFUNCTION. • OVER FILLING THE ROTOR LOADER WITH PAINTBALLS AND FORCING THE LID CLOSED WILL CAUSE JAMMING.
CAPACITY ADJUSTMENT, RAPID RELEASE SAFEGUARD SYSTEM BALL CAPACITY ADJUSTMENT The R-2 gives you the freedom to switch between high and low capacity. You can choose between 200 ball and 260 ball capacity at any time without the need of tools or spare parts. To adjust the Top Shell from the low position to the high position simply push the Top Shell Slide Button to the left, and lift the rear of the Top Shell. Once the Top Shell is in the high capacity position, release the Top Shell Slide Button. The slide button will return to its center position. The Top Shell is now locked into the High Capacity position. To drop the Top Shell to the Low Capacity position, follow the directions in reverse. RAPID RELEASE LID OPERATION The R-2 benefits from the new rapid release safeguard system. This system allows you to change between lid and quick feed at a moment’s notice depending on your playing needs. LID / QUICK FEED REMOVAL 1. Open the lid. 2. Push forward on the release button, located on the top of the hinge arm. 3. Lift lid away from Top Shell. LID / QUICK FEED INSTALLATION 1. Position the lid in the fully open position. 2. Place the spring arm in the spring retaining groove. 3. Line up the cross pins with the cross pin guides and press down. 4. The cross pins will snap into place, locking the lid into the Top Shell.
• OVER FILLING THE R-2 LOADER WITH PAINTBALLS AND FORCING THE LID CLOSED WILL CAUSE JAMMING. W
Extracted from the PDF. Read the full manual above, or download it.