Dye Rotor Manual - English

SPECS. CAPACITY: FEED RATE: WEIGHT: DIMENSIONS: POWER SUPPLY:

200 paintballs 50+ bps 1.3lbs (empty with batteries) 4.75”H x 8.5”L x 4.25”W Three AA batteries

unsure of your ability to make necessary adjustments properly,

QUICK SET-UP GUIDE BATTERY INSTALLATION No tools are required for battery installation, just follow the simple instructions found on page 2. Three AA batteries are required to operate the Rotor Loader. When installing the batteries make sure to install them the correct way by following the + and - polarity markings on the battery holder. MOUNTING ROTOR LOADER ON A MARKER Make sure the Rotor Loader is securely mounted on you marker's feedneck and the Rotor Loaders feed tube is bottomed out on your marker's feed neck. It is recommended to use an adjustable clamping feed neck system with the Rotor Loader. Do not over tighten your marker’s feed neck on the Rotor Loader as it may damage the Rotor Loader. TURNING THE ROTOR LOADER ON/OFF Once the batteries have been installed and the Rotor Loader is fully assembled, simply press the power button at the rear of the Rotor Loader (see figure 1a). As soon as the LED light indicator comes on, the loader is ready to go. There is no programming or boot up sequence to worry about, just load up paintballs and go.

Figure 1a

IF ROTOR LOADER JAMS PAINT In the unlikely event that the Rotor Loader jams paint, simply give the jam release trigger a quick pull. This will turn the center rotor arm in reverse, quickly clearing the jam. The jam release trigger is located on the underside of the Rotor Loader (see figure 1b).

call DYE or your local pro shop for help.

WARNING: RESULTS MAY VERY DEPENDING ON THE QUALITY OF PAINTBALLS USED WITH THE ROTOR LOADER.

Figure 1b

U.S. and International Patents Pending. W W W . D Y E P A I N T B A L L . C O M

CHANGING THE BATTERIES INSTALL/CHANGE BATTERIES 1. Remove the Rotor Loader from your marker. 2. Empty all paint from the Rotor Loader. 3. Open lid and slide secondary locking tab up (see figure 2a). 4. Depress main locking tab and lift upper shell off bottom shell (see figure 2a). 5. Push forward on the tab at the front of the floor tray, and lift the floor tray out of the bottom shell from the rear (see figure 2b). 6. This will expose the battery tray, gearbox and rotor carousel (see figure 3a). 7. Install batteries into battery holder. Pay attention to the + and – symbols. 8. Reassemble by following directions in reverse.

W A R N I N G

FULL DISASSEMBLY

Secondary locking tab

Main locking tab

FULL DISASSEMBLY 1. Remove upper shell and floor tray (follow directions for changing batteries). 2. The two red retaining tabs lock the gearbox and rotor carousel in place. Turn the back of the two red retaining tabs outward (see figure 3a). 3. The rotor carousel and gearbox can now be removed from the bottom shell. 4. Remove the Rotor Loader carousel first, and the gearbox second. 5. The rotor carousel can be fully disassembled for cleaning (for proper cleaning see page 7). 6. There is no need to disassemble the gearbox. The on/off button is held in place by the gearbox. Take care not to lose the on/off button during disassembly or assembly.

Figure 2a Figure 3c

Low batteries may cause the Rotor Loader not to function properly. Dirt and heavy dust can create excess friction and cause the loader to malfunction. Over filling the Rotor Loader with paintballs and forcing the lid closed will cause jamming.

Figure 3b

Figure 2b W W W . R

Figure 3a W W W . D Y E P A I N T B A L L . C O M