• THE ENMEY IS NOT A TOY. • MISUSE OF THE ENMEY MAY RESULT IN SERIOUS INJURY OR DEATH. • EYE PROTECTION SPECIFICALLY DESIGNED FOR PAINTBALL MUST BE USED IN COMPLIANCE WITH ASTM SPECIFICATION F1776 AND MUST BE USED BY THE USER AND ANYONE WITHIN RANGE OF THE ENMEY. • WEAR EYE PROTECTION DURING DISASSEMBLY OR MAINTENANCE. • GOG PAINTBALL RECOMMENDS THAT THE ENMEY ONLY BE SOLD TO PERSONS 18 AND OLDER. • THOROUGHLY READ THE ENMEY MANUAL BEFORE OPERATING. • TREAT EVERY PAINTBALL MARKER AS IF IT WERE LOADED. • NEVER LOOK DOWN THE BARREL OF A PAINTBALL MARKER. • KEEP YOUR FINGER OFF THE TRIGGER UNTIL READY TO SHOOT. • NEVER POINT THE ENMEY AT ANYTHING YOU DON’T WISH TO SHOOT. • KEEP THE ENMEY ON SAFE UNTIL READY TO SHOOT.
• KEEP THE BARREL BLOCKING DEVICE ON THE ENMEY’S MUZZLE WHEN NOT SHOOTING. • ALWAYS REMOVE PAINTBALLS AND DEGAS THE ENMEY BEFORE DISASSEMBLY. • STORE AND TRANSPORT THE ENMEY UNLOADED AND DEGASSED IN A SECURE PLACE. • FOLLOW ALL MANUFACTURER’S WARNINGS AND INSTRUCTIONS FOR PROPELLANT SOURCE HANDLING, STORAGE AND FILLING. • DO NOT SHOOT FRAGILE OBJECTS SUCH AS WINDOWS. • ALWAYS MEASURE THE VELOCITY OF PAINTBALLS FIRED BY THE ENMEY BEFORE USE, AND NEVER ADJUST TO FIRE ABOVE 300 FPS (91.44M/S). • PROVIDE THIS MANUAL, OR A COPY WITH THE ENMEY IF GIVEN, LOANED OR OTHERWISED TRANFERRED TO A NEW OWNER.
GOG Paintball USA 100 Station Street Loyalhanna, PA 15661
While every effort has been made to ensure that the information contained in this manual is accurate and complete, no liability can be accepted for errors or omissions. GOG Paintball reserves the right to change the specifications of the eNMEyTM at any time without prior notice. The latest version of this manual may be downloaded free of charge at GOGPaintball.com 5
owner’s man u a l WEIGHT:
eNMEy Manual v 1.0 Copyright © 2012, GOG Paintball SA, all rights reserved. eNMEy, the eNMEy logo, GR33SE and the GOG logo are trademarks or registered trademarks of GOG Paintball SA. The eNMEy is covered by one or more of the following U.S. Patents: 5,613,483; 5,881,707; 5,967,133; 6,035,843; 6,474,326; 6,637,421; 7,100,593; 7,603,997; 7,610,908; D535,709; D546,297; D548,201; D571,415. Additional US and foreign patents pending.
1.65 lbs - 1.86 lbs with barrel
OPERATING PRESSURE:
PROPELLANT:
CO2 or Nitrogen/Compressed air
OPERATION:
Low pressure pneumatic
ANTI CHOP SYSTEM:
Low-Force bolt
BARREL THREAD:
PAINT COMPATIBILITY:
.68 caliber standard paintballs
m aintena a i ntena nc e E
WARRANTY: GOG Paintball SA warrants to initial retail purchaser that the eNMEyTM paintball marker and regulator are free from defects in materials and workmanship over their operational life. This warranty is limited to the repair or replacement of defective parts with the customer to pay shipping costs. Disposable parts (o-rings, springs, seals, screws, rubber grips, hoses, tubing, ball detents, bottom-line ASA, etc.) are not warranted. This warranty does not cover surface damage (scratches and nicks), damage resulting from misuse, improper disassembly and re-assembly or attempts to drill holes or remove metal or polymer which could degrade performance and reduce pressure safety factors of the marker. Do not make changes to the basic marker parts without written approval. The only authorized lubricant for the marker is DOW 33 lubricant (GR33SETM). Use of any other lubricant may invalidate warranty. Paintball markers are non-refundable. This warranty is effective only if the customer registers the product online at gogpaintball.com within 30 days of purchase. This warranty is non-transferrable. Trigger alteration of any kind may result in serious injury and may void warranty.
DISASSEMBLY: The valve system in the eNMEyTM has only one major moving part, making it very simple to maintain. This does not mean it can be ignored. The eNMEyTM should be disassembled and cleaned when it shows erratic performance, becomes contaminated with dirt, paint or other debris, or for general maintenance after 3 or 4 days of use. • Unload and de-gas the eNMEyTM. Use a 5/16-inch allen wrench to unscrew and remove the bolt sleeve. • Using a soft tool like a wooden chopstick, push the bolt and bolt stop out the back of the eNMEyTM. • Clean the interior of the body and all removed parts. Inspect all o-rings for wear or damage and replace if necessary. • Lightly lubricate o-rings with GR33SETM marker lubricant. Slide the bolt stop onto the bolt from the rear. Slide the rear of the bolt into the bolt sleeve and gently screw into the rear of the eNMEyTM.
se p ett u up
01 BARREL BLOCKER: Screw the barrel into the eNMEyTM. Slide the barrel blocker over the barrel and secure its cord as far back on the eNMEyTM body as possible, cinching for a tight fit. The barrel blocker is critical safety equipment - nearly as important as goggles. The barrel blocker must be in use any time the marker is stored or handled in an area where people or property are not protected by paintball goggles or paintball field netting.
UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES TOLERANCES: FRACTIONAL ± ANGULAR: MACH ± BEND TWO PLACE DECIMAL ± THREE PLACE DECIMAL ± INTERPRET GEOMETRIC TOLERANCING PER:
PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF <INSERT COMPANY NAME HERE>. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF <INSERT COMPANY NAME HERE> IS PROHIBITED.
MATERIAL
USED ON
NEXT ASSY
Never use oil or any petroleum based cleaner or lubricant in an HPA system. Strictly follow manufacturer’s instructions.
CHECKED ±
ENG APPR. MFG APPR. Q.A. COMMENTS:
EBarrel_Blocker
FINISH
APPLICATION
02 AIR SYSTEM: The eNMEyTM is compatible with both CO2 and high pressure compressed air (HPA). Screw in style HPA systems and CO2 tanks can be screwed directly into the Air System Adapter on the bottom of the eNMEyTM grip frame. For best performance with CO2, use an anti-siphon tank or use a standard tank with a remote hose. Screw the tank in slowly so that its valve opens slowly, creating a…
The first 999 words, extracted from the PDF. Read the full manual above, or download it.