Bob Long Manual ƒ
2005 O p e r a t o r s
1799 Carpenter Road Oakley, California 94561
M a n u a l
BB oobb L oLnog ni gn t iimni tdiamt o ird a t o r
Section
Congratulations on your purchase of the Intimidator Paintball Marker. The Intimidator represents the latest in Paintball Marker technology at a very affordable price. Before operating your Intimidator, please read the entire manual carefully.
Co n t e n ts Page
Safety 2
Warranty 3
History (theory of operation) 3
WA R N I N G ! This Paintball Marker is not a toy. Misuse or mishandling can result in serious injury or death. Every person within range of a loaded Paintball Marker must wear eye protection specifically designed for Paintball. Recommended at least 18 years of age to purchase, 14 years old to use with adult supervision or 10 years old to use on Paintball fields meeting ASTM standards F1777-97. Ensure you read entire instruction manual before operating your Intimidator.
General Description 3
Introduction 4
Ammunition Aspects 5
Hopper 6
Operation 6
SAFETY!
Gas Configurations 6
Please follow all local, state, and federal laws concerning the operation and use of Paintball Markers. By purchasing this Paintball Marker “YOU” assume all liability. B.L.A.S.T. assumes no liability for injury or death due to misuse or mishandling of this Marker.
Electronics 7
Anti Chop Eyes
Board Operation 8
Powering Up 8
CAUTION!
LCD Screen 8
Never point a Paintball Marker at anyone not wearing Paintball-Approved goggles. Even at the lowest possible operating velocity, a Paintball will cause serious injury should it hit someone in the eye area.
Modes of Operation 8
Mode Selection 9
Competition Lock 10
Assembly & Disassemly
Never under any circumstances look down the barrel of your Marker. Even if wearing Paintball approved goggles, you should Never look down the barrel.
Trigger Disassembly 11
Regulator Disassembly 13
Before performing any maintenance on the Marker, ensure air source is disconnected and Marker has been degassed. Always ensure Marker is OFF whenever Marker is not operational.
Body Disassembly 15
Assembly Tips 17
General Maintenance 18
Leave the ON/OFF switch in the OFF position whenever Marker is not operational.
Consumables 18
Always insert barrel plug in barrel when Marker is not operational. Remove barrel plug only in designated operational areas.
Troubleshooting 19
Technical Specifications 21
O-ring Specifications/Identification 21
Only play at commercial playing fields that have a chronograph, referees, and clearly marked safe areas. Chronograph your Marker before each game to ensure Marker is operating at a safe velocity. Safe velocity is considered to be 280 feet per second (fps).
Screw Specifications/Identification 23
Complete Parts List 25
Introduction
Make sure Marker is not shooting at a dangerous velocity. Ensure all participants are wearing the proper Paintball safety equipment. You will be held liable if someone is hurt by a Paintball fired from your Marker regardless of fault.
The Intimidator is controlled via the MEMBRANE PAD located on the rear of the grip frame. All of the functions of the Intimidator can be easily accessed and changed through the Membrane Pad.
WARRANTY
GETTING STARTED
B.L.A.S.T. warrantees the Intimidator against damages in Manufacturing Defects only. Electrical components are warranted for a period of 90 days. Solenoids are not warranted. When utilizing after market Drop-Forwards ensure attachment bolts DO NOT protrude into internal grip assembly. When utilizing aftermarket grips ensure attachment bolts DO NOT protrude into internal grip assembly. Failure to do so may damage the internals and will result in void of warranty. Use of Teflon tape will void warranty. Aftermarket anodizing will result in void of warranty.
To power up your Intimidator, Press the ON/OFF button. To turn off your Intimidator, press and hold ON/OFF button for approximately 1 second. Buttons 1 and 2 allow the user to scroll, select, adjust, and save settings through the menus as well as timer activation, stop and reset. Pressing and holding buttons 1 and 2 simultaneously will open Menu Mode. Once in the Menu Mode, button 1 controls scrolling as well as the adjustments made to settings while button 2 controls selection and saving of menu settings. Every Intimidator is equipped with an LCD screen, located on the side grip panel (left of the membrane pad) which allows the user to verify menu settings along with voltage, timer, shot counter, eye status, tournament lock, and others, depending on the software version installed on the circuit board. A detailed description of each function can be found in the Board Operation section.
For questions concerning your Intimidator manual please call (925) 625-7929.
OPERATION The Intimidator Marker is a solenoid controlled open-bolt design. The bolt is locked onto a dual pressurized machined slider that is controlled by the solenoid (An electronic 4-way valve control). The back of the chamber is pressurized to move the bolt forward, and the front is pressurized to move the bolt backward. This allows for very low cycling pressure, as well as much less cocking recoil.
NOTE: The Frenzy Board IS NOT Programmable via the trigger.
TRIGGER ADJUSTMENT The trigger is fully adjustable using the three screws within the trigger. The upper screw controls the return spring tension, the center screw adjusts micro-switch activation point and the lower screw adjusts the trigger stop point.
GENERAL DESCRIPTION
The Intimidator is a low pressure operating, open bolt, electronic Marker, featuring microchip managed solenoid control, anti-chop eyes (ACE), dedicated low and high pressure regulators attached to a sculptured regulator mounting block, and unique patented pending modular ram sleeve.
BARREL The Intimidator comes standard with a one piece, .689 Bore, 12-inch Assassin barrel. Barrel threads for the Intimidator are Auto-cocker type.
SPECIFICATIONS
The first 944 words, extracted from the PDF. Read the full manual above, or download it.