Bob Long Defiant 2 Manual - English

Trigger Adjustment 4

Barrel 4

Specifications 4

Regulators 5

Ammunition Aspects 5

Hopper 5

Operation 6

Gas Configurations 6

Electronics 7

Battery Information 7

Anti Chop Eyes 7

Board Operation 8

Powering Up 8

Selecting Firing Modes 8

Mode Selection 9

Competition Lock 10

Assembly & Disassemly 11

Trigger Disassembly 11

Regulator Disassembly 13

Body Disassembly 15

Assembly Tips 17

General Maintenance 18

Consumables 18

Troubleshooting 19

Technical Specifications 21

O-ring Specifications/Identification 21

Screw Specifications/Identification 23

Complete Parts List 25

defiant

WARNING This Paintball Marker is not a toy. Misuse or mishandling can result in serious injury or death. Every person within range of a loaded Paintball Marker must wear eye protection specifically designed for Paintball. Recommended at least 18 years of age to purchase, 14 years old to use with adult supervision or 10 years old to use on Paintball fields meeting ASTM standards F1777-97. Be sure to read the entire instruction manual before operating your DEFIANT 2.

SAFETY Please follow all local, state, and federal laws concerning the operation and use of Paintball Markers. By purchasing this Paintball Marker “YOU” assume all liability. B.L.A.S.T. assumes no liability for injury or death due to misuse or mishandling of this Marker.

CAUTION Never point a Paintball Marker at anyone not wearing Paintball-Approved goggles. Even at the lowest possible operating velocity, a Paintball will cause serious injury should it hit someone in the eye area. Never under any circumstances look down the barrel of your Marker. Even if wearing Paintball approved goggles, you should Never look down the barrel. Before performing any maintenance on the Marker, ensure air source is disconnected and Marker has been degassed. Always ensure Marker is OFF whenever Marker is not operational. Always insert barrel plug in barrel when Marker is not operational. Remove barrel plug only in designated operational areas. Only play at commercial playing fields that have a chronograph, referees, and clearly marked safe areas. Chronograph your Marker before each game to ensure Marker is operating at a safe velocity. Safe velocity is considered to be 280 feet per second (fps).

L L ooookkss ccaa nnk k i lilll 2

WARNING Wa r n i ng

Introduction

Always ensure Marker is not shooting at a dangerous velocity. Ensure all participants are wearing the proper Paintball safety equipment. You will be held liable if someone is injured by a Paintball fired from your Marker regardless of fault.

The DEFIANT 2 is controlled via the MEMBRANE PAD located on the rear of the Trigger Frame, as well as the Dip Switch Control Panel located on the front side of the Frenzy Board. All of the functions of the DEFIANT 2 can be easily accessed and changed by using both the Membrane Pad and Dip Switch Panel.

WARRANTY GETTING STARTED

B.L.A.S.T. warrantees the DEFIANT 2 against damages in Manufacturing Defects only. Electrical components are warranted for a period of 90 days. Solenoids are not warranted. When utilizing after market Drop-Forwards ensure attachment bolts DO NOT protrude into internal grip assembly. When utilizing aftermarket grips ensure attachment bolts DO NOT protrude into internal grip assembly. Failure to do so may damage the internals and will result in void of warranty. Use of Teflon tape will void warranty. Aftermarket anodizing will result in void of warranty. For questions concerning your DEFIANT 2 manual please call (925) 625-7929.

To power up your DEFIANT 2, Press the ON/OFF button. To turn off your DEFIANT 2, press and hold the ON/OFF button for approximately 1 second until the LED turns Red and release. Buttons 1 and 2 allow the user to change the Eye Sensor’s operational mode. Once powered up, pressing Button 1 will change the Eye Sensor to Dry Fire Mode (also known as Simulation Mode), while Button 2 sets the Eye Sensor to Delay Mode. Every DEFIANT 2 is equipped with a 3-Color, Light Emitting Diode (LED), located on the side grip panel (left of the membrane pad) which allows the user to verify the current Eye Sensor Mode and/or Battery Status. A detailed description of each function can be found in the Board Operation section.

OPERATION

NOTE: The Frenzy Board IS NOT Programmable via the trigger.

The DEFIANT 2 Marker is a solenoid controlled open-bolt design. The bolt is locked onto a slotted bolt receiver that is attached to a dual pressurized machined slider (RAM), and is controlled by the solenoid (An electronic 4-way valve control). The newly designed, encapsulated ram sleeve features two chambers (one toward the front and one toward the rear). The back of the chamber is pressurized to move the bolt forward, and the front is pressurized to move the bolt backward. This allows for very low cycling pressure, as well as much less cocking recoil.

TRIGGER ADJUSTMENT The trigger is fully adjustable using the three screws within the trigger. The upper screw controls the return spring tension, the center screw adjusts micro-switch activation point and the lower screw adjusts the trigger stop point.

B ARR EL The DEFIANT 2 comes standard with a one piece, .689 Bore, 12-inch Assassin barrel. Barrel threads for the DEFIANT 2 are Auto-cocker type.

GENERAL DESCRIPTION The DEFIANT 2 is a low pressure operating, open bolt, electronic Marker, featuring microchip managed solenoid control, anti-chop eyes (ACE), dedicated low and high pressure regulators, and unique patented pending modular ram sleeve. The field strippable pull pin bolt is connected to a slotted bolt receiver that is attached to a dual pressurized sliding ram.…