SHOCKER XLS
PLEASE READ CAREFULLY
OWNER’S MANUAL
WWW.SHOCKERPAINTBALL.COM
Q UI CK START 01 INSTALL BATTERY
Velocity must be measured and adjusted to below 300 feet per PLEASE READ CAREFULLY second (91.4 meters per second) before each session of use.
02 BARREL Use a 5/64-inch hex key to remove the three screws from the left side of the wrap-around grip and lift the left side open. Attach the battery clip to a new brand-name 9-volt alkaline battery and place it in the grip frame. Carefully tuck the battery wires out of the way of the grip. Close the grip and reinstall the grip screws.
Assemble and install the included barrel. Make sure The Freak® insert is installed inside the barrel back. Install the assembled barrel in the front of the Shocker® XLS body. Take care not to cross-thread any barrel components during assembly or installation, as permanent damage may result.
03 BARREL BLOCKER & LOADER
04 TURN ON AIR
Install a high-performance paintball loader in the locking feedneck. In order to perform its at its best, the Shocker® XLS must be consistently fed unbroken paintballs rapidly.
Carefully screw a professionally filled paintball High Pressure Air (HPA) system into the Air Source Adapter (ASA).
Slide the included barrel blocker over the end of the Shocker® XLS barrel. Sling the blocker’s cords over the back of the marker and snug them tight.
Slowly turn the ASA knob clockwise to gently charge the Shocker® XLS with air.
The barrel blocker is a critical piece of safety equipment and must always be used when the Shocker® XLS is handled outside of an active paintball field.
Turn knob slowly! A quick pressure surge may cause damage.
06 ADJUST VELOCITY Turn on the Shocker® XLS by pressing and holding the power button until it glows green and the XLS data display animates. The Shocker® XLS may be turned off by pressing and holding the power button until it goes dark. Turning off the Shocker® XLS serves the same function as a mechanical trigger safety, but should not be relied on in place of a barrel blocker.
Velocity must be tested and adjusted at the start of each paintball session. Fill the loader with paintballs and turn it on. While wearing ASTM compliant paintball goggles in an area where all bystanders are protected, remove the barrel blocker and fire over a chronograph to measure the velocity. Using a 5/32-inch hex key, turn velocity up (clockwise) or down (counter-clockwise) as needed to meet the field’s standard. After each adjustment take 2 or three shots to allow pressure to stabilize, then fire over a chronograph to check velocity. For safety and to avoid internal damage, never adjust the Shocker® XLS to fire at greater than 300 feet per second.
TA BL E O F C O N T E N TS
CONTENTS
XLS SPECS
QUICK START - VELOCITY ADJUSTMENT
OPERATING PRESSURE
TABLE OF CONTENTS
POWER SOURCE
9v Alkaline Battery
DIGITAL CONTROLS
PROPELLANT
High Pressure Air
GASSES
OPERATION
Electropneumatic
MODES OF FIRE
ADJUSTMENT/TUNING PROGRAMMING
ANTI-CHOP SYSTEM
Break Beam Vision
ELECTRONIC SETTINGS
BARREL THREAD
Autococker
FIRING MODES
LUBRICANT
GR33SE TM
TRIGGER ADJUSTMENT
QEV FORCE ADJUSTMENT
FEEDNECK ADJUSTMENT
ROUTINE MAINTENANCE BOLT / VALVE
VISION TM / DETENTS
– THE SHOCKER® XLS IS NOT A TOY.
– MISUSE OF THE SHOCKER® XLS MAY RESULT IN SERIOUS INJURY OR DEATH.
REGULATOR
GRIP FRAME
– EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN BY THE USER AND ANY PERSON WITHIN RANGE OF THE SHOCKER® XLS.
ADVANCED MAINTENANCE
BOLT CONTROL / SOLENOID VALVE / QEV 18 TROUBLESHOOTING
PARTS GUIDE
WARRANTY / TECH SUPPORT
– SP RECOMMENDS THAT THE SHOCKER® XLS ONLY BE SOLD TO PERSONS 18 AND OLDER. – THOROUGHLY READ THE SHOCKER® XLS OPERATION AND INSTRUCTION MANUAL BEFORE OPERATING.
Extracted from the PDF. Read the full manual above, or download it.