“Let it rip in YOUR grip!”
Naughty Dogs Shocker SFT/NXT Board • • • • • • • • • • • • • • •
Features:
The signature board of the Naughty Dogs team Runs the new Unleashed firmware customized for the Shocker SFT/Nerve Break Beam EYE support for the new NXT line of Shockers Uses a high performance 8mHz, 4K memory processor Extensive set of tournament and recreational firing modes with configurable mode modifiers for custom tournament and breakout modes Accurate peak ROF indicator reads out the maximum BPS achieved based on a moving average during a string Four eye modes for delayed shot, dropped shot with clearing shot, eye check bypass for full speed dry-fire testing, disabled for markers without eyes or damaged eyes Seven LED color palettes to choose from Advanced power saving logic dims indicator and eye LEDs to dramatically reduce power draw during idle periods Automatic shutdown timer Full adjustability of dwell, trigger debounce, paint delay, mechanical debounce, first shot drop-off, ROF, ROF fine adjust, bypass ROF, ramp start point, ramp level, burst count, shot modifiers, auto shutdown timer, and seven color palettes Power up battery level indicator with automatic low level indication On demand selection of bypass, ROF indicator and battery condition Full LED status indication of breech, trigger, battery level and ROF readings Automatic blocked eye detection with configurable ROF reduction and recovery Automatic bolt delay setting on a per shot basis
Installation:
First insure that the air is off, and then refer to your markers instruction manual
to put the marker in a safe, non firing condition. When removing or installing the board, user must be careful not to damage the harness wiring and/or board. If you are not comfortable with this installation, please see your nearest gun technician as NoX is not responsible for improper installation. 1. 2.
Remove the grip screws on the left side (barrel pointing Left) of the marker and unfold the grip panel out underneath the trigger frame Carefully remove the battery without pulling on the battery clip wires
Remove pins holding (SFT)/Screws (NXT) down the board and carefully lift the board up. Remove old board Install the NOX board (follow your shocker manual instructions). Install Battery. a. Insure you are on the left side of the marker b. Carefully install the battery by keep the battery as flat as possible. c. When installing the battery it’s a tight fit (to insure the battery doesn’t move around). d. Make sure you don’t FORCE the battery in by Over flexing the NOX board. e. Please refer to www.buynox.com for detailed battery installation
Power Switch Functions
Power up marker: Briefly press power push button (instant on, ready to fire) Power down marker: Press and hold power push button until LED dims and then turns off (about two seconds) Read peak ROF: With tourney lock disabled, the peak ROF of the last string may be read out in blinks by briefly pressing the power push button. Check battery status: With the tourney lock enabled, the current battery status may be read out by briefly pressing the power push button. Bypass paint check (dry firing): To bypass the breech paint checking for dry firing, press and hold the power push button until the LED dims (about 1 second) and then release. The power LED and the grip LED will change their blink pattern to indicate the paint check has been bypassed. Repeat procedure to re enable breech paint checking. Even when bypassed, the eyes remain active and will read the bolt return and detect continuously blocked eyes.
Push Button LED Indicator Empty Breech:
Blinking
Ball in Breech:
Steady
Eye Check Bypassed:
Steady/Flashing
Eyes Faulted:
Steady/Rapid flashing
Grip LED Status Indicator (default palette) Empty Breech:
Blinking Blue
Solid Blue
Alternating Blue/White
Alternating Blue/Yellow
Eyes Disabled:
Alternating Blue/Red
Trigger Pulled:
Solid Green
ROF Count:
Blinking Green
Good Battery:
Pulsing Green
Fair Battery:
Pulsing Yellow
Poor Battery:
Pulsing Red
Power Management
The chip continuously monitors the idle time and automatically dims both status LEDs to 1/4 power and pulses the eye LED after three seconds of idle time and further dims the status LEDs to 1/16 power after ten seconds of idle time. Pulling the trigger instantly restores all LEDs to full brightness and resets the timer. After the configured shutdown idle time has passed, the board will automatically power down.
Battery Monitor
The battery condition may be read out at power up, on demand by pressing the power push button with the tourney lock enabled, or if a low battery condition is detected during operation. The status LED will blink rapidly in Green for a good battery, Yellow for a low battery and Red for an exhausted battery. If the battery becomes exhausted, the status LED will automatically blink Red on a ten second interval and the battery must be replaced as soon as possible to insure correct electrical operation of the marker.
Bolt Delay Monitor
The Bolt Delay is automatically calculated on a per shot basis and adapts to the actual bolt cycle speed to insure the delay is correct for all marker and lubrication conditions. The bolt delay is used to mask the false bolt return seen when the bolt pushes the ball past the eyes.
Eye Fault Detection
The board monitors the bolt return on a per shot basis and if the bolt return is not seen within a reasonable period of time, the eye status will automatically change to faulted and the ROF will be adjusted to the configured Bypass ROF. This is used to reduce further chopping when the eyes have become paint blocked from a breech chop. Should the eyes clear from continued firing or being swabbed, the eye status will automatically return to good and the ROF setting will return to normal. It should be noted that when dry-firing without air, the breech needs to be clear of paint and the bolt retracted to run the solenoid at full speed.
ROF Monitor
The first 997 words, extracted from the PDF. Read the full manual above, or download it.