NoX 06 Cyborg Board Manual - English

Carefully remove the battery without pulling on the battery clip wires Remove the screw holding down the board and carefully lift the board up, keeping track of the mounting screw and plastic washer if available

“Let it rip in YOUR grip!”

Jot down the color scheme of the wiring harness and starting at the top of the board, very carefully remove the (5) sets of wires from the board and set the stock board aside. The proper order is: a. Transmitter Eye (red/black or blue/black) b. Receiver Eye (yellow/black) c. Solenoid (red/black) d. Trigger (black/black) e. Battery (red/black)

Install the NoX board by plugging in the (5) sets of wire in the reverse order, starting at the bottom of the board. The proper order is: a. Battery (red/black) b. Trigger (black/black) c. Solenoid (red/black) d. Receiver Eye (yellow/black)

Place the white nylon 6-32 X1/4” mounting screw provided with the NoX board through the mounting hole, followed by the stock nylon washer if available and align the screw with the threaded hole in the grip frame. Using a 7/64” hex wrench, carefully tighten down the screw to hold the board in place. Only make the screw snug, not tight, as it is easy to damage the nylon screw and is not necessary for the proper mounting of the board. Note: do not use the metal mounting screw provided with the stock board as it may short out the wiring on the top of the NoX board! Attach the battery snap to the battery and install the battery into the grip frame underneath the board as per usual.

NoX ’06 Cyborg Board Instructions

Features: Runs the new Unleashed firmware customized for the ’06 Cyborg Uses a new high performance processor with 2X the speed and 4X the memory space of the stock board Extensive set of tournament and recreational firing modes with configurable mode modifiers for custom tournament and breakout modes Accurate peak ROF indicator reads out the maximum BPS achieved based on a moving average during a string Four eye modes for delayed shot, dropped shot with clearing shot, eye check bypass for full speed dry-fire testing, disabled for markers without eyes or damaged eyes Seven LED color palettes to choose from Advanced power saving logic dims indicator and eye LEDs to dramatically reduce power draw during idle periods Automatic shutdown timer Full adjustability of dwell, trigger debounce, paint delay, mechanical debounce, first shot drop-off, ROF, ROF fine adjust, bypass ROF, ramp start point, ramp level, burst count, shot modifiers, auto shutdown timer, and seven color palettes

Power up battery level indicator with automatic low level indication On demand selection of bypass and ROF indicator modes Full LED status indication of breech, trigger, battery level and ROF readings Automatic blocked eye detection with configurable ROF reduction and recovery Automatic bolt delay setting on a per shot basis

Transmitter Eye (red/black or blue/black)

Move the harness wires off to the left as to not obscure the LED if necessary, tuck the grip panel under the trigger frame, line up the two holes and using a 5/64” hex wrench mount the grip panel to the frame. Power on the marker with the slider switch and verify the jewel flashes the battery condition (green for a good battery) followed by the breech status in blue.

Power Management Power Switch Functions 1. 2. 3.

Power up marker: Slide the power switch to the on position Power down marker: Slide the power switch to the off position Check battery status: Battery condition is briefly flashed at power up. Flashing green indicates a good battery, flashing yellow for fair, flashing red for poor. If the battery condition becomes poor during use, the led will flash red every ten seconds to indicate the battery must be replaced immediately.

Trigger Functions 1.

Bypass eye paint check to dry-fire: Hold in trigger for two seconds until LED indicates white and release. The LED blink pattern will change (blue/white for default palette) to indicate the new eye mode. The marker will now fire at full speed with an empty, unblocked breech. The eyes are still functional in this mode and the bolt return is still read to moderate the cycle speed to match the current ROF setting. This can be used to advantage to tune the regulators for maximum performance with air.

Restore eye check when bypassed: Hold in trigger for two seconds until LED indicates white and release. The LED blink pattern will change (solid or blinking blue for default palette) to indicate the new eye mode. The marker will now fire normally for the configured eye mode.

Disable ROF indicator: Hold in trigger for five seconds until LED first indicates white and then turns off and release. The ROF indicator will no longer display the peak ROF attained during strings. This will not effect the eye mode.

Enable ROF indicator: Hold in trigger for five seconds until LED first indicates white and then turns off and release. The ROF indicator will now display the peak ROF attained during strings. During the display of the ROF reading, the blinking pattern can be stopped by briefly pulling the trigger.

LED Status Indicator (using default palette) Empty Breech:

Blinking Blue

Ball in Breech:

Solid Blue

Eye Check Bypassed:

Alternating Blue/White

Eyes Faulted:

Alternating Blue/Yellow

Eyes Disabled:

Alternating Blue/Red

Trigger Pulled:

Solid Green

ROF Count:

Blinking Green

Good Battery:

Pulsing Green

Fair Battery:

Pulsing Yellow

Poor Battery:

Pulsing Red