Valken RM-1 Manual - English

Rules of Safe Marker Handling

OWNERS MANUAL

1. Treat every marker as if it were loaded. 2. Never look down the barrel of a paintball marker. 3. Keep your finger off the trigger until ready to shoot. 4. N ever point the marker at anything you don’t wish to shoot. 5. Keep the marker on “safe” until ready to shoot. 6. K eep the barrel blocking device in/on the marker’s muzzle when not shooting. 7. A lways remove paintballs and propellant source before disassembly. 8. A fter removing propellant source, point marker in safe direction and discharge until marker is degassed. 9. S tore the marker unloaded and degassed in a secure place. 10. F ollow warnings listed on propellant source for handling and storage. 11. Do not shoot at fragile objects, such as windows. 12. Every person within range must wear eye, face, and ear protection designed specifically to stop paintballs and meeting ASTM standard F1776.6. 13. Always measure your marker’s velocity before playing paintball and never shoot at velocities in excess of 91.44 meters (300 feetper-second). 14. Do not use this marker to shoot at a target closer than 20 feet.

LIMITED WARRANTY Valken Paintball guarantees the RM-1 against defects in material and/or workmanship of this marker for twelve (12) months from the original date of purchase by the original retail purchaser. To activate your warranty, fill out the warranty card on the back and mail it along with a copy of the original purchase receipt. In the event that a part is defective Valken Sports will send out a replacement part free of charge. Wearable items such as o-rings, screws, ball detents, and the like are not covered under this warranty. Failure of any part due to an accident, abuse, neglect, modification, misuse, operator error, lack of maintenance, or use of parts inconsistent with the use originally intended for the marker as sold is not covered by this warranty.

VALKEN PAINTBALL

Valken makes no other warranties or guarantees, expressed or implied this marker. Valken Paintball limits its sole and exclusive liability and that of its authorized dealers, affiliates, or agents pursuant to this warranty to cover repair or replacement of the defective part. Incidental and consequential damages are expressly excluded hereunder. Valken Paintball, its authorized dealers, affiliates, or agents will not be liable under this warranty, nor under any state or federal law, the common law, or otherwise for any damage or failure, including personal injury, resulting from such use and/or alteration. This warranty gives you specific legal rights, and you may also have other rights that may vary from state to state.

RM-1 Paintball Marker Thank you for purchasing the RM-1 Paintball Marker by Valken Paintball. The RM-1 was designed to be a durable paintball marker for players of all experience levels in all conditions and to be easily maintained. RM-1 Specifications

Caliber 0.68

Action Semi-Automatic

Barrel Removable 8” ported

Power CO2 or Compressed Air (High Output)

Valken Sports - (856) 812.2800 1 Hawk Court, Swedesboro, NJ 08085 www.valkenpaintball.com

Construction Aluminum & Polymer

Velocity……… Up to 300 Feet Per Second (FPS)

Effective Range 150+ feet

Using your RM-1 Paintball Marker Trigger Safety Pin Before beginning setup, locate the trigger safety pin above the trigger. Make sure the trigger safety is pushed in on the left hand side of the marker so that the marker is not accidentally discharged during setup.

SAFETY ON

SAFETY OFF

Barrel Installation 1. Make sure the marker is degassed and that the hopper is removed. Make sure that no paintballs are in the feed port or breech. Confirm that the safety is set to “safe” mode. 2. While pointing marker in a safe direction, place the threaded end of the barrel into the front opening of the marker body. 3. Turn the barrel clockwise until it stops. Do not turn the barrel with too much force, just allow the threads to draw the barrel in until it stops. Do not over tighten. 4. Immediately install a barrel blocking device. A blocking device is any device that prevents the accidental discharge of a paintball, such as a barrel plug. Feedneck Installation 1. Rotate the feedneck lock lever down into the unlocked position. 2. Slide the feedneck onto the mounting rail from the rear all the way to the front of the mounting rail. 3. Rotate the lock lever up into the locked position until it clicks into place. Loader Installation 1. Unclamp the feedneck clamp lever. 2. Insert the loader into the opening of the feedneck until it bottoms out. 3. Align the loader so that the lid is to the rear. 4. Clamp down the loader with the clamp lever. 5. If necessary, adjust the clamp lever adjustment screw using a 3/32” allen wrench so that the loader is snug, but

DO NOT overtighten. Air Cylinder Installation 1. With a barrel blocking device properly installed, point the marker in a safe direction. Pull the cocking knob located on the left side of the marker back until it clicks and stops. This will cock the marker. Release the cocking knob and the marker is now cocked. 2. Locate the air source adapter at the base of the grip frame. 3. Position the marker so that the air source adapter is pointed upwards and make sure that the barrel of the marker is pointed down. 4. Insert the end of the threaded cylinder valve into the adapter. 5. Do not push the cylinder, but slowly twist the cylinder clockwise. Allow the threads to draw the cylinder into the marker until it stops. Once it stops, the marker is charged. Velocity…