EMP_REL_B_UPGRD_KIT_INSTR.qxd
Step 18: Carefully remove the two Halo stickers from the sides of the loader shell. If there is any dirt or paint residue on the shell where the badge will sit, apply a small amount of water to a cloth and wipe until clean. Do not use any cleaners, as the residue of the cleaner will cause the new badges to not adhere properly to the shell. Let area dry. Remove the paper strip on one Empire shell badge to expose the adhesive on the badge. Affix badge to the shell. Repeat for other side.
Installation is now complete. Please read all operating instructions before proceeding.
Empire Reloader B Upgrade Kit Installation Instructions Thank you for purchasing the Empire Reloader B Upgrade Kit! Please read all directions BEFORE starting any work. Any damages caused to your new Empire control board or to your loader as a result of attempting to install this upgrade kit are not the responsibility of the manufacturer. If you do not feel comfortable attempting this installation based on these terms, or if you need technical assistance during installation, DO NOT RETURN THE PRODUCT TO WHERE IT WAS PURCHASED.
Operating the Reloader B’s 3-Speed Board Turning the loader on: Do not load paintballs into your hopper until the hopper has been turned on. If you have already loaded the hopper, proceeding with power-on sequence may result in a jam during power-up. If this happens, simply spin the RIP drive manually to clear the jam. During the initial powering sequence, the motor will spin to prime the drive cone. Locate the power button on the rear control panel. To turn on, press the button, the green LED comes on while the button is pressed, now release the button. The green LED will now flash again for one second, go off, then flash quickly for 1, 2, 3 times indicating which speed it is currently set to. The motor will spin for a second and the loader is now ready to use. Do NOT fire your marker until after the initial motor spin has completed. Firing during this first period can disrupt the auto-adjusting sound sensitivity and cause the loader to work improperly. The green LED will flash repeatedly while the unit is on to show it’s ready. If the LED flashing changes to red, then the batteries are low and need to be replaced.
Contact: Paintball Solutions 570 Mantua Blvd. Sewell, NJ 08080 800-220-3222 http://www.paintballsolutions.com If you are not comfortable installing this kit, Paintball Solutions will install this kit into your hopper at no additional charge. Send this kit and your hopper prepaid to the address above, along with your name, return address and daytime telephone number.
Tools required for installation: Setting the speed: When the Reloader B is first turned on, while the LED flashes for one long second, press and hold the power button again during this flash. When properly done, the LED will now change to red and you can release the button. The LED will stay red for about 5 seconds, then change back to its flashing green sequence for operation if no buttons are pressed. To set the speed during the red LED phase, push and release the button the number of times necessary based on which speed you desire. Press once for normal speed, twice for faster speed and 3 times for the fastest speed. Each time you press and release the button during this sequence, the press of the button should last about 1 second. If done too quickly, the board may not be set to the speed you desire. When done correctly, the red LED will go off, then flash the same number of times the button is pressed, indicating the speed it is now set to. then the green LED will flash the same number of times if you are using the 6 AA battery pack, or the orange LED will flash the same number of times if you are using the 4 AA battery pack. The motor will now spin up at the speed it is set to, it will stop and now the speed is set and the unit is ready to use.
#1 size Phillips screwdriver and a medium-size flat head screwdriver
Turning off: Press and hold the power button until the red LED comes on, then release. When the red LED goes off, the unit is now off and the LED will not flash green.
Getting started:
This kit contains: (1) Empire Reloader B 3-speed Sound-Activated Control Board (1) Empire Control Board Back Plate (1) Battery Pack for 4 AA (1) Foam Spacer from Battery Pack (2) Empire Shell Badges If any parts are missing from this kit, please contact the address above.
Step 1: Clear a neat space to work. If possible, spread out a large, light-colored towel or paper towels on a flat surface. Step 2: Remove any paintballs from your hopper. Remove your hopper from your marker. Step 3: Remove the battery pack from the hopper. Consult your hopper’s owners manual for help if necessary. Place battery pack aside where it will not come in contact with any liquids or metal objects during installation. Step 4: Open the hopper’s lid. Step 5: Utilizing a #1 Phillips screwdriver, loosen and remove the six screws in the right side shell. It may be necessary to use one of the long screws to screw through the nuts in the left side shell in order to push out the screws completely. Pay close attention to which screws go into which holes for reassembly. Place screws in a safe place until you’re ready to put back in the end.
fully into the corner slots in the shell just behind the groove for the back plate (photo 10C).
! WARNING: ! DO NOT BREAK THE ON/OFF BUTTON ON THE CONTROL BOARD. YOU MAY USE THIS BOARD AT A LATER DATE. Step 6: With all screws now completely removed from the holes, begin just slightly separating the two shell halves. As the two halves are separating, all internal components should remain in the left side shell while the right side shell is removed by itself. If necessary, use a very small screwdriver to push the control board back plate and control board toward the left side shell while removing the right side shell Photo 6A Photo 6B (photo 6A). The on/off button of the control board extends through the back…
The first 1072 words, extracted from the PDF. Read the full manual above, or download it.