This manual provides installation and operating instructions for the Virtue DM6 Board.
Features: • •
7 Modes of fire - Semi Auto, PSP Mode, NXL Mode, Ramp Mode, Auto Response, Full Auto, and Breakout Mode. 15BPS Ready - Be ready for any tournament series! Put Dipswitch 1 in the off position, and your maximum rate of fire is capped at 15bps! All firing modes have user adjustable maximum rates of fire from 10.50bps to unlimited rates of fire! Virtue Trigger Logic constantly monitors the trigger to ensure every trigger pull is recognized, giving you the fastest responding gun, and highest possible rates of fire. Adjustable Debounce, Dwell, AntiMechanical Bounce (AMB), Eye Sensitivity, Ramp Activation Speed, Ramp Percentage, Anti-Bolt Stick (ABS). Power Efficient Software extends the life of your battery. All settings are stored in non-volatile memory so they will not be lost when the battery dies or is removed. 10 minute idle auto-shutdown saves battery life. Low battery indicator software. Forced Shot allows the marker to be fired when the eyes are enabled, but no object is in the breech. Instant On allows the marker to be fired instantly upon turn on. Tournament Lock/Unlock allows the marker to be programmed through the trigger without having to constantly open the grip. With the tournament lock enabled, settings cannot be changed without opening up the grip.
Installing Your Virtue DM6 Board: 1. 2.
Open up the grip from the right side of the marker to expose the circuit board. Remove the two screws holding the stock circuit board into place, and carefully disconnect the two wire harnesses and the battery. Remove the Stock Board from the Grip Frame, taking care to leave the two metal push buttons in place. Connect the wires you removed in step 2 to the Virtue DM6 Board, and then screw the Virtue DM6 Board into place. Reconnect the battery, close the grips, and you’re done!
Setting the Dipswitches: On the DM6 circuit board, above the two push buttons, there is a 2 position dipswitch. Dipswitch 1 is the Max Rate of Fire/15bps Cap lock. If Dipswitch 1 is in the on position, your max rate of fire is set to your “Max Rate of Fire” setting (Flickering Red LED in programming mode.) If dipswitch 1 is in the off position, the Max Rate of Fire of all modes is capped at 15bps. After changing this setting, you must turn the marker off before it takes effect. *Please note the actual bps will vary slightly from gun to gun. If the desired bps is too high or too low with dipswitch 1 down, then leave Dipswitch 1 in the up position, and adjust the max rate of fire setting through the programming menu. Dipswitch 2 is the Tournament Lock. To access the programming mode of the Virtue DM6 Board, Dipswitch 2 must be in the on position. Then hold down the trigger and turn the marker on to enter programming mode. When Dipswitch 2 is in the off position, the gun is in “Tournament Lock”, and program settings cannot be changed.
LED Indicator: Solid Yellow Solid Blue Solid Red Flashing Red Flashing Blue
(During startup) Indicates a low battery Ball in Breach; Gun is ready to fire No Ball in Breach Eyes disabled Eye malfunction
Power Operation:
To Change the Value of a Setting:
The Virtue DM6 Board uses Instant On technology. Simply tap the power button, and the marker instantly turns on and is ready to fire. To turn the marker off at any time, press the power button for 1 second.
When the LED is lit for the desired setting, pull and hold the trigger until the LED Begins to flash. The LED will flash the number of times the current value is set to. When the LED stops flashing you then have 2 seconds to enter in the new value by tapping the trigger the amount of times you want the new value to be set to. After you have set the new value, the LED will flash back at you the number of times you have just entered, and then flash through the rainbow of colors, returning to the color you have just adjusted, indicating that the new value has been set. To exit programming mode, shut the marker off.
Eye Operation: When the marker is turned on the eye system is automatically enabled. The eyes can be toggled on and off by pressing the eye button (bottom button) for 1 second. When the eyes are disabled the max rate of fire will not go over 24bps. The eye logic also differentiates between a ball being fired, and something continually blocking the eye (like broken paint, or your finger). If the eye becomes blocked, the LED will flash blue, indicating an eye malfunction. When the object blocking the eyes is removed the eye will automatically return to working mode (solid red or blue LED).
Low Battery Indicator: If your battery is low, the LED will be yellow for 1 second when you turn the marker on
If you want to change the debounce to 2 you would: 1.
Programming Mode: To access the programming mode of the Virtue DM6 Board, Dipswitch 2 must be in the on position. When Dipswitch 2 is in the off position, the gun is in “Tournament Lock”, and program settings cannot be changed. With Dipswitch 2 in the on position, hold the trigger and turn the marker on. The LED will then cycle through a rainbow of colors and stop on purple, indicating that you are now in programming mode. Tapping the trigger will then toggle through the different programming modes: Purple: Green: Blue: White: Red: Teal: Yellow: Flickering Green Flickering Red:
Programming Example:
Firing Mode Debounce Ramp Activation Speed Ramp Percentage Dwell Eye Sensitivity AMB (Anti-Mechanical Bounce) ABS (Anti-Bolt Stick) Max Rate of Fire
With the marker off, and Dipswitch 2 in the on position, hold the trigger and turn the marker on. The LED will now cycle through a rainbow of colors and stop on purple. Tap the trigger once so the LED glows green. Pull and hold the trigger until the LED starts to flash (factory default for debounce is 5, so the LED will flash 5 times). When the LED stops flashing, quickly tap the trigger 2 times. The LED will now flash 2 times, and then flash through the rainbow of…
The first 1067 words, extracted from the PDF. Read the full manual above, or download it.