TIPPMANN X7 E-GRIP KIT PART# T210001 INSTALLATION & PROGRAMMING INSTRUCTIONS KIT PN. T210001 NOTE: 9V Battery INCLUDES: Not Included, but Required ❏ 1 - X7 E-Grip ®
STEP 2: Remove stock grip from marker. ❏ Do Not perform STEP 2 before reading the warning section and completing STEP 1.
WARNING EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN AT ALL TIMES WHEN HANDLING THIS MARKER BY THE USER AND ANY PERSON WITHIN RANGE. DO NOT DISASSEMBLE THIS MARKER WHILE IT IS PRESSURIZED WITH AIR. REMOVE AIR SUPPLY CYLINDER OR CARTRIDGE BEFORE DOING ANY DISASSEMBLY. DISASSEMBLING THE RECEIVER WHILE UNDER AIR PRESSURE CAN CAUSE PERSONAL INJURY & / OR DAMAGE TO THE MARKER. DO NOT OPERATE THIS MARKER WITH PARTS MISSING OR DAMAGED. IF DURING THE COURSE OF THIS INSTALLATION, A PART IS LOST OR FOUND TO BE DAMAGED, OBTAIN A REPLACEMENT PART BEFORE CONTINUING REASSEMBLY. ❏ READ EACH STEP COMPLETELY BEFORE PERFORMING STEP. ❏ Set up a table with plenty of space to work. ) and a 9 You will need a 7/16” wrench ( volt battery. NOTE: Carefully hand start threaded parts, do not over tighten and strip threads.
STEP 1: Prepare Marker for SAFE Disassembly before beginning disassembly. Eye protection designed for paintball use must be worn by the user and any person within range. 1. Unload Your Marker - To unload your marker: ❏ 1) Install the barrel sleeve. ❏ 2) Empty and remove the hopper (turn the hopper clockwise and lift out). ❏ 3) Go to a designated firing area and remove the barrel sleeve. ❏ 4) Point your marker in a safe direction and fire several times to be sure there are no balls lodged in the chamber and / or barrel. ❏ 5) Visually inspect the CycloneTM Feeder and chamber for paintballs. 2. Remove The Air Supply - To remove a charged air supply cylinder: ❏ 1) Turn the cylinder approximately 3/4 of a turn or out. This allows the air counterclockwise supply pin valve to close so that no air will enter the marker. ❏ 2) Point the marker in a safe direction and discharge the remaining gas in the marker by pulling the trigger until the marker stops firing. This may take 4-5 shots. If your marker continues to fire the tank pin valve has not closed yet (because of the variances in tank pin valve parts, each tank varies slightly on exactly how far it should be turned) and ❏ you will have to turn the tank counterclockwise a little further and repeat step-2) until the marker does not fire, ❏ then remove the tank. NOTE: If you turned the tank and it began to leak before you pulled the trigger the tank o-ring should be checked for damage before reassembly. ❏ 3) After air tank is removed, point & fire the marker in a safe direction until stored air is completely discharged. ❏ 4) Put marker in the uncocked position: ❏ Pull and hold the bolt cocking handle back ; ❏ then pull the trigger and ❏ release the handle slowly forward to uncock the marker. (English - continued on page 2)
❏ 1) Remove the gas line from the grip: Use a 7/16" ( ) wrench to loosen the gas and then pull line nut out of the gas line the gas line elbow . ❏ 2) Remove the 2 grip push pins Press the ends of the 2 push pins ( ) in and then pull push pins out ( ) .
❏ 3) Remove the grip: Pull down on the grip to slide it off. STEP 3: Install the new X7 E-Grip . 1). Prepare E-Grip for installation: ❏ Check to be certain the is in trigger spring position as shown. ❏ Check to be certain the trigger plates have not separated and the E-GripTM trigger assembly is intact as shown. If there are gaps at between and the trigger or sear the trigger plates - squeeze plates together to look as shown. TM
Step 4: Power On - Basic Operation ❏ TOURNAMENT LOCK: Because the E-Trigger board requires a tool to turn it on and off, no tournament lock is necessary for competition paintball. ❏ 1) To turn the X7TM E-GripTM power on: ❏ Use a small object like an allen wrench ) to press and ( hold the power button for 2 seconds. will light The LED orange then green when the electronics have been activated. ❏ Release the power FA button and the green F will begin LED S flashing green to show the power is on and the battery is good. (If LED begins flashing red, see - Low Battery Condition). NOTE: If pressing the power button failed to turn on the LED light, see Troubleshooting Section on page 2.
❏ 2) Safety/Selector operation -
❏ 2). Install the E-GripTM: ❏ Slide the E-GripTM up onto the marker and align the push pin holes. ❏ Insert the two push & . pins ❏ 3) Install the gas line - Thread tape or paste are not needed for this connection.TM ❏ Insert the gas line into the E-Grip gas line elbow. ❏ Be careful that you do not cross-thread the fitting as you use your fingers to align, start and finger tighten the gas line nut several turns onto the gas line elbow . ) wrench. Complete tigntening with a 7/16" ( ❏ 4) Install the battery ❏ Remove the battery door from the back of the new grip by pulling up and back on the tab. ❏ Plug a 9 volt battery into the battery clip. ❏ To keep the battery from rattling once it is in the E-GripTM, turn the battery so the battery clip hang against the side wires of the battery, then Insert the battery into the E-GripTM as shown. NOTE: When removing a battery from the E-GripTM, Do Not pull the battery out by the wires. ❏ 5) Re-install the battery door - Replace the battery door with the tab down and listen for the snap as it locks back into the E-GripTM.
The 3-position safety/selector has switch three settings: S = Safe ; F = Semi-Auto (One pull/release of the trigger fires 1 time. FA = Special Firing Mode. The Special Firing Mode can be set to any 1 of 5 firing options as detailed on page 2 - Special Firing Mode Options. This E-GripTM is set to the factory default setting: Safe Full-Auto - Pulling the trigger three times in less than one second will result in fullautomatic firing. Holding the trigger down on the third pull will sustain this full-auto mode. The default rate of fire for this mode is 13 bps.
The first 1117 words, extracted from the PDF. Read the full manual above, or download it.